Composite Decking Front Steps Complete Tutorial

How Do You Do It?
70 followers
3 Video Views·Oct 23, 2022
I just spent the last three weeks building these beautiful new steps for our front entry. I can
hardly believe I did this myself with about $180 worth of materials as well as free armadillo
decking from our sponsor Avon Plastics. Let me show you how I put together these stairs with
no stringers. Hello everyone it's Melissa from Welcome to the Woods. Here I'm showing you what
we had before. These steps weren't centered on the door and they were too small. They really
bothered me but I did decide to build our new stairs at an angle so that they were modern and
took up a little less space. I did not know when I started this how much of a headache this would
end up being but in the end I'm so glad because the angle design looks super super cool. To get
the angle I first had to visualize because all the math in the world could not help me figure
this out precisely because construction lumber just is not precise enough for you to lay a
protractor down and figure out what angle you should be cutting. In fact the math initially
told me I needed a 25 degree angle but after laying out the pieces and measuring what I figured I
would need I decided on a 20 degree angle. So that is what I'm going to be cutting for the most part
to build these stairs. Now to cut that 20 degree angle I just laid down all the wood on my miter
saw. Unfortunately my miter saw is kind of small and so every cut wasn't quite big enough and I had
to use a hacksaw to finish it out. Kind of annoying but it was fine. The entire framework is getting
put together by three inch long deck screws. These are coated to be anti-rust and for the exterior
as well as my rigid drill set with a t25 driver. I fall more in love with my rigid drill set every
project that I do. I highly recommend them. It was really important when I was drilling these pieces
together that I had the back two lined up with my square because I want those to be perpendicular.
I will say that working with two by six treated lumber is no joke. These two by six were full
of water from sitting outside at the lumber yard and they were super super heavy. Cutting them was
a total pain and driving into them I broke three different drill bits during this process before I
wisened up and started using titanium drill bits only. So the lesson here is when you're working
with treated lumber don't mess around. Use sharp blades, strong drills, and the correct bits and
screws for the job. You'll see that here where the joint comes to an angle I had to cut both ends
of the lumber at a 20 degree so they fit together nicely and I did that on the other side as well
to create a complete trapezoid. Here I'm flipping over my trapezoid to begin to screw in the joists.
The joists I just used two by fours so by flipping this over it is saving me time. I'm going to use
the floor in my garage as basically the level to get all the joists to be flush on top with
the top of the platform. Does that make sense? So each of these joists I cut to basically match up
with where they're going to be on the trapezoid angle. This was a lot of measuring and trial and
error so that each joist is spaced 12 inches apart. 12 inches apart is the recommended joist
spacing for the composite decking material that I'm going to be putting on the top of these steps.
After screwing in all of the joists on the top platform it was done and it was time to move on
to the steps. I created the steps a very similar way to the top except there were no perpendicular
angles. Everything was a trapezoid so I had to cut a lot of 20 degrees and I turned each of the
stairs into its own box. Now here you can see I'm just securing all the ends. Now you have to account
for the thickness of the material that you're going to be laying on the steps and because my
decking is about an inch thick then the first step needs to be shaved to account for that and have
all the steps be even. Does that make sense? So I'm building steps that are six and a quarter inches
tall but I have to account for an inch thick decking so that made my first step be five and a
quarter inches tall. Here you'll see me shaving down some of the two by sixes I used to build that
slightly shorter box for the first step. Instead of measuring 12 inches again for all these joists
I just put a speed square next to the joists that were on the top platform and then marked
where to put the joists in each step. While it probably wasn't necessary I also cut each of the
two by four joists on each box of stairs at an angle so that they lined up perfectly with the
platform on the top joist. Now the reason I did that is because I'm going to have some screws
visible on the top of my decking and I just wanted everything to go in a straight line
and look really nice. Now here I'm taking scraps of two by six that were left over and screwing
them into the back of the bottom step. These are going to help me rise up the box for the second
step because the second step is actually going to lean on these. Now you'll remember the first
step I shaved down to five and a quarter so it was really serendipitous that the height of these two
by sixes plus the height of the two by six second step equaled a six and a quarter inch rise.
On the back of the second step I attached two by six pieces at an angle to kind of create a
leg system as well as a couple more along the back and this gave it the same amount of rise
in the back as in the front where I had those pieces of two by six resting against the first step.
A lot of the connections for the legs I was only able to achieve because I had a Kreg jig mini
which allowed me to drill pocket holes at a 45 degree angle install so if you're interested in
getting a Kreg jig mini I have one linked in the description on this video. Here I'm using it to
drill pocket holes at a 45 degree angle in the second step that later on I will secure screws
down into the support pieces I put on the back of the first step. So I also am going to be drilling
a ton of pocket holes using my Kreg jig K4 which has like the clamp system and everything to build
up legs for the third step which is the big trapezoid platform. I created a u-shaped leg
structure for the platform, five of them actually, and I actually turned the two by fours different
directions so you'll see here I'm attaching some of the legs with the two by fours like parallel
but then I also did some of the legs where the two by fours were turned perpendicular and this
is to prevent the top platform from tipping. Once I had all three stairs risen to their perspective
heights I took a piece of outdoor rated plywood and this is three quarter inches thick and I'm
drawing a line for what I want to cut out with my jigsaw to create like a door along the sides
now the reason I'm not just keeping it solid is if you'll remember the corner of the area where
the stairs are going to go has a faucet and the intake pipe for our furnace so because I'm using
composite decking I'm not worried about that intake pipe being underneath it'll have plenty
of airflow. You can see them here as I move away this basket that is where I want to create a
little door with that plywood on the side of the stairs and just have it kind of blocked off so I
don't have any animals or whatever making homes underneath my stairs so I'm just getting things
prepared here to move away the old black stairs from our front entry. Now these were really
really heavy and I cannot believe I'm telling you this right now but I basically moved these
by myself. Here's how I did it. Initially I tried to get it away from the house and I couldn't.
My husband has been working from home so when he was on a very quick short break I think he had
like five minutes I asked him to come outside and help me and we moved the steps maybe six inches to
a foot away from the house and then he had to go back inside. How I moved the steps was I grabbed
a little two by four and I grabbed my dolly so I used the dolly and I shoved it underneath the
front of the steps and then I tilted the steps up slightly with the dolly just to slide the two
by four block under there with my feet. Then I had space to get the dolly out of the way and lift up
get my fingers under there and lift up the stairs. This was very heavy. What was even worse was when
I had the stairs on their side trying to figure out how to scooch them out of the way. I had to
use my whole body especially the strongest part of my body which was my hips and legs to push
against the house and a lot of adrenaline helped with this to get these stairs moved. I would say
these were hundreds of pounds but if I can do it anybody can do it and no I did not hurt myself.
I was fine the next day. Then I just gave the area a clean sweep and it was time to assemble my new
stairs. So I brought in the steps first the two steps and I'm going to be attaching these
like I showed you earlier with the pocket holes that I pre-drilled. I love to do my projects
myself but unfortunately I needed my husband's help again during his next five minute break
to bring in the top platform because it was just really large. I guess it was okay we make a pretty
good team. The area where the faucet was unfortunately was obstructed by one of my legs
and so I had to cut out more of it than I wanted in order for the platform to fit where it needed
to go. I used my oscillating multi-tool which you just saw and cut out part of the leg. Fortunately
it was still pretty sturdy. Now we're going to make this beautiful with this armadillo decking
in the color campfire. Thank you to Avon Plastics who sponsored this product for us.
Composite decking is maintenance-free and takes these special screws. They have color-matched
heads so that they're nearly invisible when put in and they have two different thread types you
can see that hold the screw into the composite decking as well as into your framework. It's best
to pre-drill on this composite decking before installing these screws in order to prevent
mushrooming which happens because composite decking is theoretically just made of plastic.
It doesn't behave the same as wood even though you can cut it just like wood. I would recommend
getting fine tooth blades and making sure that you are not over driving screws because they can
easily get stripped in this type of material. So I am using my impact driver here but I'm taking it
really slow. The reason that I made the dimension of my steps to be six and a quarter inch rise is
because that accounted for the thickness of this material and the seven and a quarter inch tall
riser boards that came with the decking so it's all going to work out really great. You can see
here that I'm using a little spacer to screw down the edge of my first board for the top platform.
This edge needs to get screwed down but the other ones don't because I'm going to be using
turbo clips. More on that later. I'm just going to pause here and show you this because it's a
funny clip I accidentally recorded of my kids walking by. This is how you work with kids.
They're constantly in the way. I get that question a lot. Anyway, all the boards for the top platform
I cut at an angle to go against the house side and then I am actually using these turbo clips
like I mentioned earlier. They're a strip of screws that are ready to go in these plastic
spacers that help you perfectly space out and secure down your decking boards without having
to screw down in the top. So it kind of just looks like they're floating and it's so beautiful. The
installation goes really fast. When each of your turbo clips are screwed in you just lay the next
board next to it and push the groove into the turbo clip and then screw down your next line.
It's important to tap with a rubber mallet as well just to make sure all your spacing is even.
Now this was really tricky. When I got to the angle where I met the house by the front door
I used my jigsaw again and I set up this straight edge for myself to cut this really tricky angle.
It's a 20 degree angle where all the ends of the board meet the house but then on the side where
it meets the front door it was like a 20 degree angle the other way. Does that even make sense?
It was a very very sharp angle. You see that? And then I also had to notch out there by where the
threshold for the door bumps out. When I figured out that angle I made a cardboard template which
I'm showing you here just so I didn't have to measure every time and I could repeat that angle
again and again. So I laid the whole top step this way and this is the corner. What I did was
I got one turbo clip in there to hold down that last board and then that little corner I just
stuck a screw in there to hold it down and make it safe. If you're still watching at this point
kudos to you and you might like to know that I brought along my Instagram audience
in behind the scenes footage of building these so go ahead and follow me on Instagram
if you would like. The link is in the description on this video. Here I'm using my table saw to
rip down the riser board for the bottom. You'll remember that that one was height adjusted so
the riser board had to be as well. And with the riser board of course I pre-drilled all of my
holes. Super super important. Sometimes these decking boards would be a bit bowed but fortunately
they're very malleable. So you can see I'm using a few different tools to kind of get the spacing
even throughout before I pre-drill. And then I screw down to hold it into place into the joists
and I just move my spacers as I go and keep drilling down and that by the end my boards were
like perfectly spaced and it all looked great. For the steps themselves I had a ton of pre-drilling
and screws to install because the turbo clips are not rated for steps. Overall I really loved
working with this product and I hope it's as durable as they say. You know one thing that I
like the most about it is that it's made from 95% recycled material and Avon Plastics where I got
it from told me that they process a billion plastic bottles a year to make these products.
So I think that is super super impressive. Here I am using my jigsaw again just to shear off the
ends of all the boards. I didn't cut these individually before install because I thought
this would be easier to just run a straight path. I used my oscillating multi-tool again
to finish the cut near the house where the jigsaw couldn't reach. At this point the entire top of the
stairs was covered but I'm going to install some hinges to create that door on the side that we
talked about. I made the door as small as I could because initially I was planning to do the whole
thing swinging open with plywood as you can see here but it ended up being too heavy with the
riser boards on top and just too long so I cut it down into three pieces. One piece is closing off
the side of the two bottom stairs and then another piece is going to go up here where I have a 2x6
obstructing the entrance anyway. So then I'm covering it in riser board and this is covering
up all the edges of the cut pieces of decking that go along the top and this is going to look
so nice. Now my only cut edge showing is along the front. For the rest of the door I needed a vertical
cut so I used my scroll saw because it was the thinnest blade that I had and that's going to
make that cut less noticeable. You'll see what I mean here in a minute. So the first piece gets
attached to the side of the step itself. The other part of the opening is going to be the door that
swings open. So this piece of plywood is going to be my door and this will allow me to access the
faucet. This is where I'm going to attach my hinges and then I install the other piece of riser board
to the piece of plywood hopefully making the cut seam line up really nice and be pretty invisible.
I don't even know if you noticed until I'm calling it out here but did you see that I even cut the
edge of the riser board at that 20 degree angle so that it becomes flush with the front of the
stair? Seriously you guys I had no clue when I was making these at an angle it was going to be
so complicated. Anyway once I had the door put together it looked pretty good but I needed a
because it didn't stay closed on its own of course. So I installed a little old-timey cabinet
latch that I just had laying around. You could also use a powerful magnet for something like this.
Finally after three weeks of work I was done with all of my cutting and man did I have a big bag of
sawdust to show for it. I gathered all of this just to throw away because it's technically not
wood that's biodegradable. I just put it in a bag and put it in my trash. The finishing touch was
mixing up a paint color that was going to match. I used some red some orange and some black to make
this brown and just painted the edges of all of the cut seams and that was it. I'm done and this
is how I felt. There's nothing like that feeling of accomplishment when you complete a DIY that
you weren't completely sure you could pull off. These stairs are one of the most complicated
things I have ever built and I hope you're impressed with all of the angles that I figured out
and the beauty of this design. I love how they come up to our front door. I love how precisely I
tried to cut everything. I think I did a pretty good job if I do say so myself and more than
anything I love the beautiful decking that I got from armadillo decking. The color is just perfect
to set off my neutral black and white house bring some warmth and some welcome into our entry.
So here I'm just showing you how my little door works to sneak in there and hook up the hose to
the faucet when need be. Also I'd like to know in the comments would you ever attempt to build
something like this? Let me know below if I inspired you and thank you guys so much for
watching my stairs build. I hope that if you were impressed you click share on this video.
We'll see you next time on Welcome to the Woods.
