How To Make A Crosscut Jig For Your Table Saw

DIY Creators
91 followers
42 Video Views·Dec 10, 2022
Hey what's going on guys I'm Glenn with DIY Creators and today we're going to be
making a trip over to the table saw. We're going to be making a sled for that.
Really simple using your existing miter gauge and you can take the same concept
and build a full sledge sled. Now the best part about this is the footprint
that it actually takes up. All you want to do is just take your miter gauge and
attach it to it, detach it from and you can actually just find a place to mount
it to your table saw. We're going to show you just how to build that so let's get
into the video. As you can see here I have two sheets of 3 quarter inch
plywood that sandwiched together. I'm going to first start by cutting off one
of the rough ends then I'm going to run it through the table saw and hope to
create a straight edge. After making the first pass I'm going to sit the plywood
on top of the table saw just to see if I got a straight edge. And since I didn't
see any gap I'm going to trust that this is accurate and now I'm going to make my
second pass cutting the plywood down to the desired size. And after measuring I'm
going to take this over to the miter saw and remove what I don't need. The sled is
designed to use the miter gauge and I need to take the thickness of this
because I'm going to duplicate that for the opposite side of the sled. And to
assist me with this I'm using a digital caliper. I'm going to use this because I
think this is the best method to get that pinpoint accurate measurement. And
when you're making measurements using a caliper seem to be the most precise way
to get the right and correct spacing between the saw blade and the saw fence.
And this tool give you three point of measurements. One you can see you got
depth you also get inside and outside measurements. Since I've already ripped
the width of the track now I'm going to do the depth of the track and I'm going
to mark this so I don't cut it the wrong way. And when you're cutting a piece of
wood so thin like this you want to stay as far away from the blade as possible
so use scrap wood or whatever it take to push and guide the wood through the
blade. As you can see the wood is flush with the top and it doesn't interfere.
Now place the fence in front of the miter gauge and square that up with the
blade. The next thing you'll want to do is take a piece of scrap wood and sit
that on the back side of the fence. Now mark the track on the opposite side of
the fence so that it's flush with the front side of the fence. Now cut the track
to the line so that this piece will sit at the bottom side of the fence. The next
thing you'll want to do is find the center of the fence then put a mark on
it. I want this to be centered with a saw blade but this is all based on
preference you could always have this favor to one side. And I'll square this
up once again and clamp the fence to the miter gauge. And this way everything is
in a fixed place and I can focus on drilling the two mounting holes. Now
first I'm gonna start by drilling a couple pilot holes so I know exactly
where to drill it. And even though I started off drilling freehand it's
always best to use tape or collar so you don't go all the way through. Next take a
larger bit to open up the hole for the inserts. And the more I use these I'm
really starting to fall in love with them. I really love these insert they
just seem simple and just seem like a no-brainer to use. Now if you're gonna be
assembling and disassembling like I would be doing here a lot with this setup
this is probably the best way to go because I have thread in place and I'm
not necessarily ruining the wood. And using these threaded insert over the T
nuts these also leave you with a cleaner surface on the opposite side. Next I'm
gonna jump to the other track in a table saw I'm gonna place a piece of painter
tape down within the track with the sticky side facing up. Now the small
piece of track that we cut earlier I'm gonna add glue to that then place that
on top of the tape. Now place the fence on the track then take the other piece
of wood sit that in place as well take the tape and lock the three together. Now
this way when you clamp it all down I can lift the track out and everything is
together then I can flip it over and add a few screws. And since I'm working with
such a small piece of wood it's a must that you pre-drill this so that you
don't split the wood. Now I do believe adding a scrap to the back side of the
fence makes sense because it actually gives me more space to add another screw
and also provide more support. My initial plan was to just mount the t-track to
the top side of the fence but when I got to this point I realized it just made
more sense to flush it within the wood itself because it would just look a
whole lot cleaner. Now after I made the first pass I dropped the bit a little
more then I dropped it for the final time so I made three passes. Now the
router bit I'm using here is the perfect size for this size t-track but since I
hit a screw in a previous project this tapered the end of the bit and don't
allow the proper width. Now I do have a second bit the problem is I can't find
it and I need to get to moving on this project so I'm just gonna take the
chisel and remove the jagged edge. So at this point I can now move on to sanding
down the project removing all the sharp ends on this thing all the plywood
splinters and round over some of the corners. Now I attached the t-tracks and
I was happy with that but then I just thought that I wanted to put some
shellac on here because it looked a little plain and I didn't like the way
it feel with the rough texture on it so I just added some shellac sand it down
with a couple coats on it and I was happy with that. Now the assembly process
is pretty simple just drop it in place and tighten up screws and you always
want to make sure that you double check for squaring that everything lines up
every time you cut just so that you're cutting accurately. Now because I forgot
to put my safety glasses on as I made a first cut through the table saw I did
realize that sawdust was pretty much flying at my face and that's when I
decided to add a piece of plexiglass on top but then the problem is my stop
would get in the way and that's when I had to go back to the drawing board
again and decided that I wanted to add a hinge so that I can make that flap back
and forth so that I can get it out the way. Now if you've ever installed hinge
before you know how much of a pain it is to install a screw right in the center
of the hinge and that's where these bits come in they're made for that and it
actually works out really well. I'll have links down in the video description if
you want to check those out. So the nut on the screw needs to go down inside the
wood when the flap is down so I'm going to take a Frostner bit or a larger bit
and drill down into the wood but I got to keep in mind that right below that is
the two screws that I just installed and I want to make sure I don't interfere
with those. Now the good thing is here I can see right through the plexiglass and
then I know exactly where to mark the two holes for the hinge. Now I'm gonna
trust that I marked those hole well enough I'm gonna pre-drill them and then
open up the hole big enough for the screws to pass through. And now to
assemble this you want to make sure you keep the plexiglass on top of the hinge
then you want to install the nut and also the screw and at this point you can
tighten them up and lock them in place. Now I need to find the center and mark
it so that I can line it up to where the blade come through the fence. Next I want
to flip it over so that I'm on the backside of the plexiglass then I want
to mark where the two screw holes is gonna be. So for me I'm not gonna make
this so that it's permanently attached. Now if you don't feel like there's a
need to detach it and you want to keep it permanently in place and you could
always do that just use wood glue but for me I want to be able to take it off
at will. And with the pre-drill holes already going through just mark the
fence and then open those up so that you can install the threaded insert. And
these just make it a whole lot easier to attach and detach anything you want. And
just make sure you install them and screw them in all the way so that the
top of it is flush with the surface. Now you can butt this all the way up to the
fence but because I had these plastic washer that came with a TV bracket. Now
let's say you like this feature and obviously you may not have these plastic
washers. What you can do is just use a piece of wood in each corner glue those
on as spacers so that you do get the light coming in from the side but you
can also look down and see the blade exiting out the backside of the fence.
Now adding the t-track and the stop to the fence just make it more convenient
because everything is in one place and if you want to take that a step further
you can always add a tape measure on top of that just so you have accurate
measurements. Now as you can see I didn't allow the stop to come down any lower or
make the fence any shorter and that's because if I wanted to in the future I
can always add a piece of plywood here and that way it's future-proof. Just keep
in mind if I wanted to make repeatable cut that's lower than the actual stop I
have here I can just add a piece of wood in place clamp that down and then I can
just go to work. If set up correctly you can get accurate cuts every time. If
you've never used a crosscut sled before and you own a table saw these things are
awesome they're probably the best way if not the best way to make repeatable cuts
on the table saw and you don't have to worry about kickbacks. Now one of the
best thing about this particular setup is the footprint it takes up in your
shop. This one basically you just break it down or you take it off your miter
gauge and then you just store it anywhere you can actually just attach it
to your table saw. It's always better to show than to just explain so I'm going
to show you how you can use this to make a dado joint and just how simple it
could be. Now if you have a dado stack you can always make two of these one for
your regular blade and then one for your dado stack. Using a standard table saw
blade you can see that this require a bit more of an effort to remove all this
material. Now what you want to do is you want to make the two outer cut first and
then work your way in the middle and just remove all the pieces an eighth of
an inch at a time. At this point you've removed as much as you could so all you
need to do now is just clean out the dado slot using a chisel. Now just drop
the piece of wood into the dado slot and here you have it. And we're back. I'm
going to tell you all the things that I like about this and then also the things
that I think can be added as an addition to this. Now obviously if you want to add
a piece of wood that sit on a surface of a table saw as well you can totally add
that on to it. The other thing I would add on to it is adhesive tape and that
way you can have easy measure outs when you're doing repeatable cuts. Another
positive I have on here is the dust guard. I don't always grab my safety
glasses as I didn't while I was building this and the dust went flying at my face.
So you know that really helps out and I think it'll be a great addition and you
should totally add one if you happen to make this. Now what's actually nice about
this thing is the footprint it takes up. I think that's the biggest catch and the
biggest positive here is that if you have a small shop or if you don't have
a place to store a lot of jigs and all those extra pieces I think this may be a
solution for you that you can literally just attach it to your table saw put it
on top of a cabinet put it in a drawer that's big enough to house it and I
think it's really also great for the small shops and it's also great to have
on a job site especially if you have a job site saw you need to make cross cuts
on the job site and this a solution like this may works out well for you. If you
find these videos helpful support me over on Patreon. Patreon slash DIY
creators that way you guys can help me create more content and that's it for
this one guys if you like this project and smash that thumbs up and let me know
what your thoughts are down in the comment and don't forget to turn on your
notification so that you get notified every time we upload over here and oh by
the way I've been working on my signature exit. I'll see you next time
