【修理】WE G18C GBB 內外管固定法

Thank you for watching this video, I am NoYoC Don't forget to leave comment to tell me your ideas and share your own Airsoft Experiences! I believe most of the people who bought the WE GLOCK will also encounter the same issue like me The projectiles will be deflected away from the normal trajectory The situation will be much more complex because of the design of the movable inner and outer barrel makes more variables This issue bothers me for almost 1 year Because I can't find out an appropriate method to get the barrel fixed Luckily, I found it recently And this method doesn't need too much skill So I think it can helps many players Let's go to the next phase now At first, I will talk about the issues There are 2 issues The 1st issue is the trajectory is abnormally deviating to left side The 2nd issue is the trajectory is unstable Let's talk about the 1st issue Most of the players who bought the WE GLOCK should have encountered issue that the trajectory deviates to left And most of the data are showing the proofs that the culprit is the hop rubber That's true, the hop group has some issues I have encountered the issue either But for the sake of convenience, I replaced the whole hop chamber, barrel, and hop rubber The accurate has also increased For how to install the inner barrel and the hop rubber I will make a video to explain it After experiencing some Airsoft gameplays I noticed that the trajectory is deviating to left on my GLOCK That means when I aiming the center of the target, the BBs will hit at the left side of the target Although I have red dot to Zero it But I will see the red dot is really deviated to left On overlooking angle, it looks like I am aiming the right of the target After the checking It's the issue but not related to the hop rubber It's the issue which related to the inner and outer barrel, hop chamber, and the tolerance Here is my slide that I am using In theory It should be a straight line from the muzzle to the end of the slide However, the tolerance issue between each part that make them shaking It becomes the reasons that the trajectory deviates to left and the trajectory is unstable So if you can't hit the target accurately may not be the problem on the shooter Although in most situations it is What issues will it occur? For my own experiences My weapons almost zero in 8 meters So I can hit accurately anywhere in 8 meters However, let's extend the range up For example, the normal combat range around 20~30 meters I notice that the range is much farther, the trajectory is much deviated to left Please keep in mind The adjustment of elevation and windage has a limit My red dot quite deviates to the left when zero in 8 meters There has no enough space to adjust the red dot if I would like to zero in 30 meters If I am in a gameplay, I almost not check the range But this may miss the target any time Generally, the main purpose of this video is trying to fix the issue that the trajectory deviates to left But when I did the change The 2nd issue, the unstable trajectory issue is also improved So this method should be applied to most players Let me explain how did I do to fix it There are 2 places that need to be fixed The 1st one is the inside of the slide The 2nd one is the outside of the inner barrel Before starting it, there are 4 items need to be prepared The 1st is the cotton swab You may also use the tissue, but I prefer the cotton swab The 2nd is the cloth tape It's thicker than the electrical tape It will be much convenient than using the electrical tape The 3rd is the utility knife The carving knife or any others that can cut off the cloth tape is okay The 4th is the scissor, to cut off the cloth tape Let's check the slide first The trajectory is apparently deviated to left on my pistol So I have to stack up the left side and fix my barrel Okay, so the thing is simple First thing is clean the inside of the slide by cotton swab Generally there may have a lot of silicone oil It needs to be cleaned first Otherwise, the cloth tape will be hard to stick on it In fact, it's still hard to stick after cleaning the slide And now, stack the cloth tape The size of the cloth tape must not get stuck with the notch of the slide If the tape has enough thickness, try to put it inside of the slide to test it if it can prop the outer barrel If it can't, keep stack up the tape The thickness should be fine if the tape can't put into the gap easily between the outer barrel and the slide In order to get the outer barrel fixed and can be removed An appropriate thickness is required Next step is make a notch on the cloth tape Just use the utility knife to cut the cloth tape on the center It needs an enough notch It would look like an U-notch if done it Next step is put it in the inside of the slide This cloth tape can't really stick on the slide But it actually helps me move the position easily Just put the outer barrel into the slide when it's done To check if the outer barrel can be assembled and get fixed If the outer barrel can't be assembled Just tear off the tape Then tear off a layer of the tape from the sticky surface After that, stick it in the inside of the slide to test it again On the other hand, just stack up the tape Repeat the steps until it can be assembled and get fixed Let's check the inner barrel It will be easier than the outer barrel At first, there has one point that needs to know There has a circle that shrinks inward by 1mm in the outer barrel The tape must avoid getting stuck on this place, otherwise, there may have some problems Generally, to test the weapon first if the outer barrel gets fixed This may help you understand if the next adjustment is necessary On my own situation, the trajectory is still deviated to left So what I have to do is prop up the left side of the inner barrel However, there has a big gap between the inner barrel and outer barrel, it must be stacked up until the gap is gone I would still use the cloth tape The tape must stick on the center of the inner barrel, but a bit close to the muzzle It can't be stuck on the muzzle because the inner barrel will be a bit going forward when pulling the slide The tape will stuck on the circle of the outer barrel that I mentioned a while ago I can't promise if these issues may happen such as the pistol may not load the BBs or the Gas in low efficiency So I would like to prop up the left side The tape can stick on the left side first Then keep rolling it The tape can be cut off if the thickness seems enough The tape must be cut off on the left side, so it won't prop up the wrong direction Let's assemble it with the outer barrel Generally, it should be a bit tight And can't be too loose If it's too tight, the slide can't not work well If it's too loose, it may not help get the barrel fixed The thickness must be found out by yourself The slide should be hard to be pulled after the cloth tape stick on the inner barrel The issue may be solved if use some silicone grease to lube it or cut off 1 round of the cloth tape Let me introduce one more place that can help get the barrel fixed It's Hop chamber I've mentioned this in the beginning, this position will also be shaken apparently due to the tolerance issue My main purpose is to correct the trajectory to the right So cut off a piece of the cloth tape, and stick it on the right side of the hop chamber Remember, this must not be too thick For the cloth tape, one layer is enough There is one more place, which is the ejection port on the outer barrel This place can also stick up the cloth tape It can't be too thick either And the size of the cloth tape must be big Otherwise, the cloth tape may be torn off and make the slide stuck when the slide is pulling and forwarding These places can also use the silicone grease to lube it To avoid the cloth tape getting tore off Don't forget this important thing The fixation of the inner and outer barrel process is done These parts should be tighter than before On my own opinion, the trajectory is still deviated to left but improved so much The unstable trajectory is also improved Okay, this is the solution that I found out I had some other ways to do it, but it seems useless So it really took so much time for me to find this way out It should be much convenient if you have 3D printer Just print it off and polish it, and the appearance would be much beautiful But keep in mind DO NOT make the inner too tight The inner barrel may be bent Here is a bad sample to show you. The T-N.T. barrel that attached on my WE M4 GBB has been bent due to I tightened the inner barrel So do it carefully I hope this method can help you increase the accuracy It improves 2 issues on my G18C which the trajectory deviates to left and the unstable trajectory One of the problems on the GLOCK is the movable barrel In order to get higher accuracy, you have to spend much money to buy a fixed barrel But it's not fit for me because I would like to DIY I would also like to hear your suggestions to improve the weapons It may be a trick, but it can also help others And make the whole Airsoft environment much friendly Don't forget to leave your comment to tell me your ideas and share your own Airsoft experiences If you really love my content, kindly subscribe my YouTube channel, and lit up the bell next to the subscribe button If you would like to follow my texts and images content, kindly visit my social media in the video description, Like and Follow it! So you won't miss any news from me! Okay, hope I can see you in the next video I am NoYoC