自己動手換易拉寶裡面的掛圖

The tools are a tape two screwdrivers one crosshead and one flathead the one used is definitely for the end this depends on whether there are screws on the pop-up banner then a wallpaper knife that's the tool On the banner there is a front and a back this part where the handle is attached is the back and this is the front You need to clearly distinguish the front and back Usually when this pop-up display is opened and facing forward the port is on its left side On the left after opening just open it like that and flip it open It has screws so if there are screws use a screwdriver to remove them There are four screws if you don't have any then here is a plastic clip just break it and the clip will open This one is the same but you only need to hit one side This side the pop-up display rotates around this axis and there is a tool inside which is a small pin This pin is very important as it is specifically used to fix the pop-up display If you can't find one there are plenty It's lost but that's okay You can go find a nail or make a thicker wire You see I can prepare a wire like this and put it here Then it remembers which direction the banner is it just hits one side it only uses this one side Then flip it over it's still facing forward forward start pulling down one person can do it It has a hole this screw is used to fix it this is very important it's on this shaft this is one of its shafts there is a shaft here there is a hole next to this shaft it has many holes but only this one hole is functional this one hole This pin is inserted to fix it because when we pull out this pull-up board it automatically retracts inward When replacing it it shouldn't retract inward so this pin fixes it just one pin Of course this pin comes with it but if you don't have one you can find a nail or a thick wire yourself When you switch it you look at it it's facing forward you should note that it's facing forward when installing it a common mistake is to put it backwards with the screen facing inward that's reversed and then it's all for nothing So as you did before just look at it and then start rolling pulling it out it's facing forward when you cut the image this image is also facing forward slowly loosen it then insert it Then you can take this which comes with a sticky paper and tear it forward tear it forward and remove the old one and put the old one aside So take the new one we're going to replace it with note that it's facing forward this is the front so when you cut it make sure you don't cut it backwards that would be wrong align it properly It has a line cut it straight along this line each one has it definitely it's wired because it's explained to two people This instruction there's a note here how to cut it you see where to insert the plug then use tape to secure it then pull it through then I'll show you how to cut it actually just align the wire straight Because if it's not straight it will tilt inward and break the width isn't consistent there's a mark cut it there's no tape just cut it straight Cutting straight is mainly about cutting the line straight the width is in the middle so it's straight then just cut off the tape on both sides That's all because I made the tape stick better it's more adhesive just cut it once If the tape is very thin or doesn't have enough tensile strength you can flip it over and cut it again on this side to reinforce it This tape does not need to be cut very long it can be cut very short cut a little or can be fully applied or not fully applied Because it's too thick there's resistance when it curls so I just apply a little bit to fix it and prevent it from coming off and that's it What is the purpose of unfolding it it's just that it has a part that is pulled down and pressed down What if you want to open it just press it like this After opening it press it again like this It doesn't matter if you press it back and forth basically just press forward pressing forward means to align it and push it into the seam Press and hold press once after pressing it turns on These two people do one one person does one one person does it like that For two people you pull one person can slowly pull the head in from the side If one person does it take it all back After pulling it back you need to pull it tight Once it's tight you can pull out this leg You must pull it tight and step on it with your foot Pull it out slowly and pull it back in At this point don't loosen it completely if you loosen it too much it will break so loosen it slowly Loosen it slowly it will pull in it has power It sometimes tilts you see it's a bit tilted then you pull it again What does the pop-up display you often talk about look like At this point we just take this thing Each display stand comes with this small tab Put it back in after using it it has a magnet It's a slanted display board there's a magnet on this side place it here then when you take it down There is a clip just pry it up like this That's how you usually hold it so it won't come off like this When you want to take it apart usually this pin If you push this pop-up display forward it's on its left When you snap it like this you can see a latch here Just snap it like this and it comes off It's mainly about the design many people don't use it because it breaks easily When placing it this is all you need to do