Watch This Before You Start Jewelry Making!

Hello everyone, welcome to my channel. In this video, I would like to show you the spiral bracelet model. We could also call it a fake prison scheme. Because when you put on the steel cable, it kind of resembles a prison. It could also serve as an alternative model for those who cannot carry out the prison work. It can also be done via radio. I want to show you the ingredients. 8-number sand beads. Black sand. The black beads. We use size 8 and size 11 glass beads. The copper, mint, red, and blue colors you see here are all number 11. Let me show you. If you wish, you can work on the middle section in a single color. You can use multiple colors like me and change the model. 20-millimeter exam. We use single-layer. We're taking the longest. Liquid silicone. Royal brand needle. Number 100. Button needle If you have it, please provide it. Helicon thread. You can also use it as a walkie-talkie model. 2 capsules closure. These were probably 8 millimeters. That's all the materials. We can proceed with the production right away. Because it is a model that wears more pants. At the beginning, we extend our duration as much as possible. Now we put on our matching outfits. 5 pieces of size 8 black beads. We will take 7 pieces of size 11 bead. I took five black ones from eight. 7 pieces of 11-numbered clay beads. If you want size 11, you can also get them all in solid colors. If you want it to spiral like mine, with different colors. You can also get one like mine, colorful like this. You must continue to follow the same color sequence as you initially established. You will change the colors if so. Let's wrap our fingers around it. We're going up only 5 steps from the black. We are pulling. We don't need to tie the knot at the beginning. Then we'll look at the node. We'll take 1 black one. We will buy the same beads here again. A black one. I got 7 items with number 11. The bead color sequence is the same again. Just as I first received it. Blue, red, mint, two copper. Now let's once again wrap our fingers around this. Let's hold it here in our hand to prevent it from coming out again from below. It will tighten up in a couple of rounds. We don't leave the IP on the other side. We are sending these down here like this. We wrap our fingers around it. One second. After we wrapped it around our finger. This black bead we acquired later. Down four from this black. 2, 4 count down. Four from below and black from later, that is, a total of each time, each time, each round. We've just acquired a black one, and we'll pass five black ones from the bottom. We will do the same procedure again. We endured it. We place these beads on top of the previous beads like this. We wrap it around our finger again. We are taking the same numbers again. I got the same numbers. I'm doing the same thing. I'm throwing it toward Arkaya. How to avoid wearing it out. Because we initially took it too long, it needs to last all the way to the end without wearing out. We're tossing it down like this. It's a bit tight at first, that's all. After that, the model becomes easier as you proceed. The beads we just took, 1, 2, 3, 4, down below. That is, counting beads 1, 2, 3, 4, 5. We pass through five black ones from bottom to top. We've passed it. Like this. Slowly. As we progress, our tasks will become even easier because they will grow shorter. At first, a bit difficult. I pulled it. We are paying attention here. Not from here. We are leaning forward like this. We're done, then. We are getting old. The same numbers and the same order. The string of beads here shouldn't be messed up. We always take the ranking in the same way. We are sending it below. We wrap our fingers around it. 5 beads. Black only. We are going up from the fifth floor. We are installing it. That is to say, like this. When we pull it, this is the resulting image. A picture like this appears. We lean it here every round so we won't be surprised. The figure began to emerge. Again the same numbers. We complete the same process again, this time according to the third one. Let's complete the same numbers by applying the same technique. I'll finish it. I'm done. If you're going to make it wireless, you'll create attachment points on these end parts. You will take 6 beads. You'll be banned from here. You'll strengthen it by going around a few times. Similarly, leave the rope at the beginning a bit longer Then you will make a mounting point here as well. Let me show you like this. To make it more resemble prison work I will use a helazon stick inside it. I had stretched my thread out too, too long. That's all that's left. Therefore, be careful to make the rope quite long. After finishing, if you're going to wear a bracelet We're tying the knot right here, right now. After the bite, like this It's a bit troublesome now that it's shortened. A few turns, a few knots are sufficient here. Because I stick the appliance with silicone. That's why it's already strong enough. Let's tie another knot here too. This many nodes are sufficient. We untied the knot like this We are doing it. Similarly, we hadn't skipped the node at the beginning either. We hadn't tied the knot at the beginning. You can thread the thread we have separated onto the needle if you wish. You can thread it onto the needle and tie a knot. I'll tie a knot like this before that. I'm passing by like this. Now I'll wrap and pull a few turns. I tied my knot without needing a needle. I will move the knot away from the beads and then burn it. Now I'm threading a few beads through. I advanced a few beads. I'm pulling. One node is sufficient. We burn our knot without cutting here or setting fire to the thread on the beads. Now we will place this in the middle part onto the helazon wire. Like this. We installed it using a rope. If we shift them a bit like this, we'll ensure the beads sit snugly against each other. Like this. It really resembles prison work. As an image. Now there's such a skewed impression. We will also put on the capsule cover, thus freeing ourselves from that image as well. Like this. First, we will apply a small amount of liquid silicone into the capsule cap's interior to ensure it remains solid and stable. I poured the liquid silicone. We'll curl this end now. We twist it like this with our fingers. Now, when we do the same process here, we are doing the same thing here as well. Our readiness is like this. After the silicones we are currently using solidify, these areas will become completely immobile. If there is excess silicone protruding outward, we can clean it off with our hands. It's better not to play too much until it dries up. Let me also show you the prison-related matter. This prison affair is, of course, even more orderly. If you can't perform the spiral stitch, at least you can work more easily with spiral models. As I said, you can also make it without using steel wire. You can also do it without using a helix tube. I think it would look much better if gold were used instead of these copper ones. I hope you liked my video. If you liked it, don't forget to click the like button and subscribe to my channel. Goodbye, until we meet again in different models.