Walkie-talkie using Arduino, humm.. sounds interesting isn't it? Alright, lets spend some time today and design and understand this fairly simple circuit, and lets find out how our expectations are challenged by the reality.
Support My Work BTC: 15cNh9hup8jidCVPwa1DTcxeoh2FPijVrX LTC: LbquH9Ku78vHtcm3LZnWXpD1JQWdKzeV4v DOGE: DEB2QBAihnBRhGsaB8P7kz559TDiucQhX6 ETH: 0x5d8c9ba0e54d8354d4af81871db26daa190d2194 BAT: 0x939aa4e13ecb4b46663c8017986abc0d204cde60 LBC: bZ8ANEJFsd2MNFfpoxBhtFNPboh7PmD7M2 COS: bnb136ns6lfw4zs5hg4n85vdthaad7hq5m4gtkgf23 Memo: 572187879 BNB: 0x5d8c9ba0e54d8354d4af81871db26daa190d2194 Thanks, ca again in my next tutorial.
Walkie-talkie using Arduino hmm sounds interesting isn't it? All right let's spend some time today
and design and understand this fairly simple circuit and let's find out how our expectations
are challenged by the reality. This video is sponsored by PCBWay. PCBWay specializes in
manufacturing of very high quality low volume colored PCBs at a very budgetary price. In addition
to standard PCBs you can order advanced PCBs, aluminum PCBs, rigid flex PCBs. They also provide
PCB assembly and other related services which can meet your need at the greatest extent. While
compiling data for my tutorial on the NRF24L01 module I found this easy to use RF24 audio library.
This library has all the basic functionalities that you need to make a DIY walkie-talkie. The
sketch is very simple and I had all the components required to assemble this on a breadboard. To
motivate me even further I found tons of video tutorials of people making this super cheap
gadget with crystal clear voice transmitted over 1 to 2 kilometers of range. Hmm sounds a bit dodgy
but I still wanted to give it a shot. The audio library works on top of the RF24 library. Let's
start by looking at the schematic of the circuit and let's also find out the components required
to assemble this circuit. Before going into much details let's understand the basic requirements of
this circuit. To transmit and receive data from one unit to the other we need some sort of transceiver
module and a microcontroller to process the data. We need some sort of module to capture our voice
and a device to convert the sound wave received in the form of electrical signals and relay it
as an audible sound wave. To start the transmission we need a push button and a LED indicator which
lights up when the transmission begins. Similarly at the receiving end we need a LED indicator that
lights up when the unit starts receiving data. Alright now let's replace our logic with the
electronic components. The heart of this circuit is an Arduino Nano. The voice is transmitted from
one unit to the other using an NRF24L01 transceiver module. Using a microphone module connected to the
A0 pin of the Arduino I'm going to capture my voice and using a 8 ohm 0.5 watt speaker
connected to the D9 and D10 pin of the Arduino I'm going to output the voice received by this
circuit. To initiate the transfer I'm using a push button switch connected to the A1 pin of the
Arduino. The red LED connected to the push button lights up when we press the button and transmit
data. The green LED connected to the D6 pin of the Arduino lights up when the unit starts receiving
data. We also need to add a large decoupling capacitor anything from 470 microfarad upwards
on the 3.3 volt line to filter out voltage spikes and to provide enough power to the IC to keep the
voltage stable. You may also need to provide additional power to the NRF24 module using a
3.3 volt voltage regulator. To transmit and receive data we need exact copies of this module at both
transmitting and the receiving ends. Now let's have a look at the code. Unless you want to do
something super funky just go ahead and upload the minimal code provided with the RF24 audio
library to both the Arduinos present at the transmitting and the receiving ends. The code
works perfectly fine with the circuit diagram we discussed in the previous section. If you want to
change any one of the pin combinations then you need to edit the userconfig.h file which you can
find inside the Arduino libraries folder. That's all you have to do to get this all up and running.
All right now the interesting bit. Let's go ahead and test this super cheap Arduino based walkie-talkie.
As you can hear the sound quality is a total disaster. I tried few things like altering the
sampling rate, altering the transfer speed, adding a better microphone and an amplifier circuit but
nothing helped to improve the audio quality. This circuit is a total disaster. I feel like I wasted
my weekend making this project and I'm glad that I did not end up designing a PCB for this setup.
Frankly speaking with this setup you can only get about 20 meter or less with concrete walls in
between. So if you have a little faith in me don't waste your time making this project at home.
Thanks again for watching this video. I hope it helps you. If you want to support me you can
subscribe to my channel and watch my other videos. Thanks. See you again in my next video. Bye now.