How to Carve a Female Face in Wood | Full Step-by-Step Tutorial

Artistic Strokes
2 followers
Nov 16, 2026
AI Generated·May contain errors
Howdy folks, welcome to the channel.
Welcome to this lesson on carving the female face.
Just a quick note before we get started
that the extended version of this video is available to
supporters on Patreon. Patreon supporters get additional lesson content
and patrons who support
in the learn to carve tier get the chance
to send me photos of their carvings and I send back
a detailed review and some advice on how I think they can take
their carvings to the next level.
So with that said and out of the way, let's get right into the lesson.
Howdy folks, welcome to the shop, welcome to a new lesson video.
Today we're carving a female face in cottonwood bark.
I'm starting with a 25mm No. 3, and I'm just removing
the outer material to create a semi-rounded surface.
Alright, the first thing I'll draw is the vertical center line
that'll go right through the nose, down the lips, to the chin.
And a circle, which represents the width of the head
and the bottom of the circle,
will be the bottom of the nose.
And the top of the circle, the hairline. And a cross section
through that circle to represent the brow ridge.
And then between that brow ridge and the bottom
of the circle, I'll double the distance
to indicate the bottom of the chin. I'm also
sketching on how the flowing hair will frame the face.
I'm drawing on the ball of the nose
And the two nostril flares beside it, and notice how
the nostril flares are smaller and they sit a little bit higher.
So the bottom of the nose has a slight V shape. It's not totally flat.
Alright, now I'm carving in the brow ridge using
a 16 millimeter number 8 gouge and using a 7 millimeter number 8 gouge.
Carving that V shape below the nose.
Also defining
the bottom of the chin.
And now I'm taking back these two angled planes
from the tip of the nose to the forehead and then
from the tip of the nose down to the chin.
I'm using a 25 millimeter number three and taking
back this recessing plane that goes from the tip
of the nose all the way back through the forehead.
Our goal here is to have
the nose sticking out further than everything else. And this other
plane from the tip of the nose down to the chin.
And this angle is a little bit steeper.
And now I'm just redrawing the lines that I carved away,
so the circle and the cross-section
brow ridge and my center line.
And now re-establishing
that cut for the brow ridge
to separate the brow ridge from the lower part of the face.
Now I'm drawing on this
sort of trapezoid shape to block out an area for the nose.
And you can see I'm using that
Number three, too.
Just kind of make these sweeping cuts just to block out the nose.
And I also take the angle of the eye width between the eyes.
And there's about half an eye width on either side of the eye.
The next step is to carve the eye mounds.
And I'm drawing this sort of half circle underneath the eyes.
And then carving along with this number eight.
This is a seven millimeter number eight.
And I carve up to the interior corner of the eye and then I like
to come down from the top or sometimes you can reverse that order
and start from the top, carve in and then just take the gouge out.
Don't try to come out of that cut. Just come back from the other side
and try to meet it in the middle like that.
I find that's the best way to get a somewhat clean result.
And I'll do a few passes to get a good amount of depth.
And I'm focusing on getting more depth in the lateral corners.
We'll get more depth in the interior corners
a little bit later with a smaller tool.
Next I'm using this bird's head finishing gouge
to make a smooth sweeping cut
underneath the eye mound.
And this elevates the eye mound above the level of the cheek.
Here I'm just redrawing my center line to ensure some symmetry.
And taking a bit off of that side
of the nose to make it match the other side.
Now I'm using a 7mm number 8
to carve the outline
of how the hair frames
the face all the way around.
Dividing the area beneath the nose into thirds
to identify the placement of the mouth and of the chin.
The mouth has this semi-curved line in the middle
and then these sort
of downward sloping lines on either side.
Which almost looks like she's going to be frowning,
but trust the process, it ends up looking very different in the end.
That's just the natural shape of a resting mouth.
We're going to go in with our V-tool here,
3mm number, what is that, a number 12.
And we are carving in that little semi-curved shape,
which helps us get the middle volume of the top lip.
And then we'll carve those downward sloping lines on either side.
And now I'm going in with a knife
and just kind of rounding off those sharp edges that we just
made with that v-tool on the bottom lip and then also on the top lip.
Now we want our top lip to
stick out further than the bottom lip
and so don't be shy to remove a little bit extra material on
that bottom lip side.
Now in this next step we're doing two things at once.
We're defining the shape of the chin
and we're also separating the bottom lip from the chin
and we'll start to see the bottom lip kind of
come together a little bit pretty soon.
I'm just doing this upside down U shape for the chin,
getting extra depth on the corners or on either side.
And now I'm drawing in the area where the
nose will go, the outside edges of the nostril flares.
It's about the width of an eye.
And now also we are taking our 16 millimeter number eight
and I'm carving this deep channel
that extends from the nostril flare down past the corner of the mouth
and down to the chin. So this
kind of frames the whole front side of the lower half of the face,
which includes framing the mouth,
framing the chin from the rest of the jawline,
and then also framing those nostril flares.
And after I carve that channel,
I'll then remove the material on either side of that cut,
so carving the cheek material away.
And I'm also working on the outline of the mouth,
more or less. We're going to continue refining the outline of the mouth
Throughout the carving, so this is just kind of roughing it in.
But just taking away that material.
We're doing a lot of different things all in the same cuts here
because this also takes the chin and jawline back a little bit.
So we're really starting to rough in all the major shapes and forms
of the lower half of the face here.
Next I'm extending the corners of the mouth,
getting a little more depth in those corners of the mouth
and starting to bring that jawline up a little bit more
And also defining.
The chin, separating it from the bottom lip a little bit.
And in each of these areas,
we are still not really anywhere near the final levels of depth.
But this is the way carving works.
With faces, you have to get a lot of depth in some areas,
and it's always wise to do a little bit at a time.
And make adjustments as you go.
You'll see on this project there are a lot
of adjustments that are made later on.
And so right now we're just focusing on getting
the forms roughed in and kind of sketched out.
And you can see I sketched in the philtrum with a little number 8.
That was a 7mm number 8.
The philtrum being that little scooped out bit
of material that connects the nose to the top lip.
Now I'm using the edge of a V-tool, the flat side, to start to shape.
I'll do the same for the lower lip.
Notice how the upper lip is made up of three volumes,
and the lower lip is made up of two volumes,
and they sort of nestle into each other.
They kind of almost fit together like a little puzzle piece.
I'm drawing on these angled lines where the side of the face
really starts to get a lot of depth.
It's roughly from the cheekbone down
on an angle that tapers down towards the chin.
You can see those angled lines I've carved
in really deeply with a number 3, that 25 millimeter.
Number three, and after that I'm starting to further shape
and define the chin.
I've also drawn on something that resembles more of the lip line,
the outer outline of the lip,
and you can see the mouth is starting to shape up
and also taking that jawline back a little bit.
And we'll do more of that later,
but we're just doing little bits at a time.
And now I'm going to start to shape the structures of the nose,
starting with the ball of the nose or the tip of the nose.
And the nostril flares, which are basically three circles
or spheres that are all kind of squished together in a way.
And I'm starting by taking a 7mm number 8 to carve
in that ball of the nose, carving all the way around,
almost up to the bridge of the nose, but leaving a little bit
of material where it connects to the bridge of the nose.
And also carving down underneath, it's important
to also shape the bottom part of the main ball of the nose.
Now drawing on the bridge of the nose, which
is a little more narrow than the ball of the nose.
And that just helps to get a more typical feminine appearance.
A big wide bridge of the nose will tend to look more masculine.
And now roughing in the nostril flares.
Starting with a number 8.
That's a 4mm number 8 right there.
A bit of a smaller tool to get more depth.
And it's important that these nostril flares
are recessed in to the cheek.
So that when you look at the nose from the side profile,
it looks like the nostril is going back into the cheek.
And it's more the tip of the nose that's actually sticking out.
This is a good angle right there.
A ton of depth.
That's a three millimeter number 11 to get even more depth
and just working on refining
all the structures of the nose there.
Now using a four millimeter number eight
to get more depth in the interior corners of
the eyes.
And I'm also shaping the transition
from the bridge of the nose to the eyebrow ridge.
We don't want that to be...
A right angle with a sharp corner in that interior corner.
We want that to be a nice, rounded, smooth, gradual transition.
Now getting some more depth, sides of the mouth,
separating the corners of the mouth from the cheeks,
the barrel of the mouth from the sides of the face.
Using a number 5 gouge
to carve these channels almost
that separate the cheek from the barrel of the mouth and the chin.
And we're just going to continue to carve away,
get a little more depth.
From the side profile here, you want to be able to see
the corners of the mouth coming back on both sides here.
So you can see how much of the mouth you can still see
from that side profile.
We want to avoid a flat mouth.
So that's what we're doing in getting more depth here.
Okay, now I've drawn on some markings where I want
the high point of the cheekbone,
which sits just outside
corners of the eyes and just below the eyes as well.
And I'm going to start carving
quite a lot of depth to get some really good depth
and dimensionality for the sides of the face
and also making sure that I leave that material for the cheekbone.
It's a really helpful
Full feature, if you want to get a feminine look.
higher cheekbones that are a little bit more defined
and then just around the perimeter of
the face they're quite hollowed out
so you'll see me go back many times to make adjustments
and refine those cheekbones
but we've just kind of barely roughed them in here and now i'm further
refining the chin with that sort of upside down
u shape and i like to get extra depth
in that area directly beneath
the lower lip to separate it from the chin
So I'll use a 4mm number 8 and eventually switch
to a 3mm number 11 to get some extra depth just below the lip.
Now I'm further taking back the jaw, the chin,
also shaping that lower lip a little bit,
bringing it forward from the surrounding area.
Now with my carving knife,
I'm just trying to refine the shapes that I've already created,
getting rid of any awkwardly jagged looking...
areas from the rough out stage.
Also taking the bridge of the nose back a little bit to create
more of an upturned nose,
which is another feature that's typical of both youthful and
feminine looking faces. Okay,
we're going to now focus on the three major planes of the forehead,
and the frontalis muscle kind of defines these planes. This almost
trapezoid looking shape again with those angled lines
and the brow ridge will sort of follow
these angles here and i'll show you
from the bottom view it's really helpful to look at it
from here these three sort of angles and planes
so you can see how the brow ridge sits on those
slightly recessing angles
and then right in the middle that plane is somewhat more flat
And then it also extends upwards.
to the sort of top portion of the forehead
which on the female face is quite tall and sticks out a
little bit more like females will typically have more volume
on the top of their sort of forehead
whereas the male forehead will have more
of a steep angle going backwards now here i'm taking
Kind of the side of the head where the brow ridge meets the temple
and kind of turns into the side of the head.
So I'm taking back the material in a pretty steep angle right there.
Now drawing on the eyebrows.
I realized I wanted the eyebrows
to be a little bit more straight across.
I thought they looked a little bit like
the brow ridges were angling down,
kind of creating almost a sad look.
So I wanted to raise those eyebrows up a little bit.
Now I'm identifying that.
Fatty tissue right under the eyebrow that kind
of sits on the underside of the brow ridge.
And it's a nice rounded volume of material that we'll carve on later.
So I drew that on as well as the top eyelids,
where the top eyelid meets the eyeball.
Also just figuring out those proportions again.
Now I'm using a 3mm number 11 to start carving where
the upper eyelid meets the eyeball.
Not going in too far here,
and I'm using a rounded tool instead of a V-tool,
because it's easier to make adjustments after.
And once those are carved in,
I will take a knife and start to round that material underneath.
We want the upper eyelid sticking out further than the eyeball,
so I'm reducing the material under that cut,
as you can see from the side profile there,
and also rounding it, right?
We're thinking about the eyeball as a spherical object, more or less.
Now I'm carving the area where the upper eyelid meets the brow ridge,
so really focusing on that upper eyelid itself,
and once again with the 11, 3mm 11, carving a line, and then using
the knife to refine that shape, take it back into that crease.
Now this is a part that many people miss
in carving the female face, which is the
area between the upper eyelid and the underside of the eyebrow.
That transition should be
a soft smooth looking volume of material. So that kind of oblong
rounded looking shape that I drew in earlier,
I'm now carving around that to create
A volume, or a mass of material, and I'm trying to make it
a soft transition from that eyelid to the eyebrow.
It'll really help once we get the sandpaper out
to further soften that structure.
Now I'm drawing on the eyebrows and...
Taking a small, that's about a number six gouge,
maybe four or five millimeters, and I am just
tracing around and then elevating the eyebrow mass
from the rest of the forehead. Now I'm turning my
attention to the outline of the face,
narrowing the temples while not removing any material right
where the cheekbones are, but then
also kind of hollowing out the material underneath the cheekbone.
It might seem like I'm jumping around
a little bit at this stage, and I kind of am.
That's genuinely how my process works,
especially halfway through a carving like this,
where you can chip away a little bit on every feature.
I didn't want to change my genuine working process just
because I'm filming a lesson video.
I think, or at least I hope,
that you guys will appreciate seeing how my process actually unfolds,
rather than seeing, you know...
Some version that I'm changing things just because it's a lesson.
So hopefully you guys aren't thrown off
by how I'm jumping from one feature to another right now.
So now I'm going back to the lips
and shaping those two volumes of the bottom lip.
And how they kind of nestle up like a puzzle piece to the top lip.
The three volumes of the top lip.
And softening those corners.
And now thinking about the outline of that bottom lip.
Shaping it with a knife.
And then underneath that lip line,
really scooping that material back so that it connects nicely with
that jawline and the chin.
And while I'm working on the lips,
I decided to refine
the upper outline
of the top lip as well. This is a three millimeter number three,
a pretty flat, very small gouge,
which is really useful for defining this top line of the lip.
Now, if you want to
Lower the outline of the lip, bring it down a little bit.
You can actually carve away material
on the high side of the cut with a knife,
and that's what I'm doing here.
So bringing that outline of the lip down
by carving away on the high side.
Okay, now back to the eyes.
I'm drawing on the shape of the lower eyelid,
and it really kind of tucks
into the lateral corner of the upper eyelid.
And I'm using a number 11, making sure that the outside edge
of the tool is following along with that line.
And now going in with a knife and really trying to get some more depth
in those corners of the eyeball to really round that shape nicely.
And now I'm taking a V-tool,
once I'm happy with how things are sitting, and carving
in some more crisp, detailed, sharp lines for...
The crease of the upper eyelid and I will
also do the same where the eyelids meet the eyeball to
crisp up those lines and you'll see later
on in this carving I still end up making adjustments
to open the eyes. I thought after I carved the pupils
and the details of the eyes she was
looking a little sleepy
so you'll see that adjustment happen later on but now
Looking at the transition from the brow ridge down
to the bridge of the nose down to the
ball of the nose. Sort of this whole continuous structure.
I'm just using a, I believe that's a
four millimeter number three, to refine that ball of the nose,
refine the bridge of the nose, and
notice that smooth curving transition up
to the sort of interior corner of the eyebrow.
Just really trying to give more definition
to these structures that we've already partially carved in,
including the nostril flares.
And once again, notice how they're
really recessing back into the cheek.
And I'm using the tip of my knife to really refine
the shape of these nostril flares
as they sort of come and wrap around the nostril
and meet the tip of the nose.
It creates an unclean cut, right?
I'm just kind of relying on the material to flake off.
And then I will clean it up later, as you can see here,
with this little, I think that's a two millimeter number eight.
Now I'm going to take you to the bottom view of this carving
and notice how you can still see the separation of the tip of the nose
or the ball of the nose from the nostril flares.
So I'm going to accentuate that here by carving down.
And really separating those areas
for the nostrils from the ball of the nose.
And you should be able to see that from the bottom view as well.
Now just crisping up those nostril flares where it meets
the cheek with a small V-tool
to really just crisp those lines up.
Now I'm doing another pass of refinement on cheekbones
and hollowing out those cheeks.
Really a really useful feature in getting
that feminine look is to have high cheekbones that are
Really well defined
and I'm working to try to make them more symmetrical here, too
so just making little adjustments to that structure of the cheekbones
and how they kind of come up and
Connect with the rest of the face.
We're at a stage of the carving now where all
of the main structures are pretty much established and
what I'm doing is just
Bouncing around and making little adjustments.
So I noticed that the jawline was still a little bit too
sharp and square and
Sticking out a little bit too much. So I'm taking the chin
and the jawline down even a little bit more there
Okay, now to the details of the eye. I'm starting with this little dot,
which is like the little reflective bit of material,
to give the illusion that it's like a glossy looking eye.
Then there's the pupil. Notice how you can't see the full circle,
but it intersects with the top eyelid.
Now drawing on the iris, wrapping around that.
And to carve in these structures, I'm going to start with this 2mm
number 8 and just sink it in to isolate that glint of the eye.
Then I will actually carve around it.
And this defines the whole entire iris,
and the pupil will sit inside of that.
Just cleaning it up, and now I like to go around
with this 1mm V-tool just to crisp that iris line up a little bit.
Also clean up that area underneath the little glint.
Now to get the pupil, I'm actually using a Dremel bit.
This is a little pokey diamond bit Dremel attachment bit.
And I'm just basically poking around
that little glint to create the pupil.
Because, you know, I can't really get in there with a carving tool.
Sometimes I will actually cheat and use the Dremel,
but it works just as well with this soft cottonwood bark
that you can just kind of poke it
in and get pretty much the same effect.
All right, now we're going to start sanding.
I'm using 220. It's an old piece of sandpaper,
which is nice because you can fold it up into little shapes
and get into all the nooks and crannies.
And so I'm just sanding the face,
trying not to sand away too much material.
And also using these drill bits, which I have a bunch of,
they're different shapes, have different
sort of rounded tips
or pointy tips to also kind of help shape the structures of the face.
After doing one pass of sanding,
you can then start to reevaluate the face and see what could
use some refinements. And for me,
the outline of the face is still looking pretty sketchy.
I think that there could be some more subtle refinements
of structures around the bridge of
Edge of the nose.
Once again, going back to those cheekbones, I think I must have done,
you know, like 10 or 12 rounds of refinements just
to really get the cheekbones to the right level of definition.
Okay, now carving the details of the eyebrows,
the actual hairlines, and notice how closer
to the middle they're kind of sticking more almost up,
and then as you move towards the side of the head,
they start to become more horizontal.
And also they have, you know, each of them has their own kind of wispy,
whimsical, curved shape to them.
But the general trend is closer to the middle,
pointing more up, closer to the side of the head,
pointing more sort of horizontally.
And then just, you know, having some fun, adding some variation.
Now for carving the hair, I like to break it up into primary sections
and then add the details on top of those primary sections.
The primary sections sort of define the overall direction of flow
and main layers of hair.
So I'll draw them on, sketch them on using curved lines,
S-shapes, thinking about how
I want the hair to move around the piece.
And this will be different for every piece of wood.
Take a lot of artistic license on this.
As you can see,
Below the face I have these two main strands
or sections of hair that are kind of sweeping
across underneath the chin
and then the sections of hair on either side of the face are kind of
wisping out. So I used a number 8 to define those main sections
and then rounded them off with a
knife. Now I'm going in with a V tool to make
those separations between the main strands even more crisp
Now for the detail lines on each section of hair,
I like to look at the overall form of that section
and then try to just exaggerate that form even more
so that each individual hairline
kind of more or less takes the form
of the primary section of hair that it's sitting on,
but with a little bit of variation and a little bit more movement.
So I'm placing detail lines right next to each other,
but they are converging and diverging away from each other,
so that there are no two lines beside each other
that are exactly the same.
Now you can see how within each section,
the detail lines are following the pattern of that section,
but with some variation, right? They're not all exactly the same.
Some lines are converging with others
while diverging away from other lines,
and there's some variability in the movements.
Okay, now we're in the final adjustment stage.
I've kind of gone through all of the steps
that I usually will go through,
and it's just a matter of looking at the carving
and seeing if there's anything jumping out
that looks like it could use some refinement.
And that's actually usually a lot of work.
This is a big stage of the finishing process of the carving
to make all these little minor adjustments and refinements.
So you saw I reduced the chin.
It was still a little bit too sticking out.
And now I'm separating the planes of the forehead a little bit more
and also taking back that top
part of the forehead where it meets the hairline.
I thought it was sticking out a little unnaturally,
a little too tall looking. And this was a key one. Here I am
opening the eyes a little bit more.
I thought this girl was looking a little sleepy,
so just removing a tiny amount off
of that upper eyelid really went a long way.
In making the eyes feel a little bit more alive and open.
And you saw how I was using just the edge,
that flat edge of a V-tool there.
Now another one that helped a lot on this piece is hollowing out
and refining those cheekbones a little bit more.
And also I wanted to add this detail on the outline of the lip using
a 3mm number 11 gouge to just trace around the outline of the lip
and then use a knife.
To sort of remove the inner material,
refining those shapes of the lips, and that creates
this crisp-looking outline of the lip.
That really helped with this carving,
and here you can see I have that carved magnolia
flower on the top.
I'm doing a lesson on carving the leaves
and the magnolia flower for this project
over on Patreon. So if you would like to become a Patreon supporter
and support this channel
and get more wood carving lesson material, then head over there.
It's in the link in the
description of this video and you can sign up.
And yeah, I hope you guys enjoyed this video.
Hope you got a lot out of it.
Keep on carving and we will see you in the next one.
