Milwaukee doesn’t make this CAT6 tool, so I did

The Tech Toolbox
1 follower
AI Generated·May contain errors
Does this look familiar?
What about this?
That is a Milwaukee hacksaw straightening Cat6 cable
in under two seconds,
and somehow nobody is making this tool.
I've been a part of over 100,000 Cat6 terminations,
and this is the tool I wish I had for every one of them.
But getting here took a $500 machine from AliExpress,
a Power Wheels battery hack, a tire inflator.
Is the battery on the air pump?
Really?
And one very humbling afternoon on a ladder.
I need another hand.
I've got a lot of work to do, so let's get into it.
A few years ago, we had a project come through
the shop where we had to build 50,000 Ethernet cables.
That's 100,000 terminations.
And since I'm a nerd, I've done some terminating of Ethernet cable,
but only a few at a time.
So I was immediately struck with,
how are we going to do 100,000 of these?
I started looking for some more industrial options, and I found this.
Little toy, which I guess is okay
if you're terminating a few cables a day or if you're
an IT pro on the job site,
but it just was not going to work to do 100,000 cables.
So I got on the Googler
and started searching around for a more industrial option.
Now there wasn't a lot out there.
I saw a few videos, but as far as finding a product,
the only thing I was able to find
was this little Chinesium
unit right here.
This is a Cat6 cable straightening machine,
or at least that's what the Alibaba listing
said it was.
It didn't really have any instructions, reviews,
one short video, but I was out of options
so I shelled out the $500 and had it sent over.
Let me show you how it works.
All you have to do is load the cable,
hit the footswitch, and your cables are nice and
straight and ready for terminating.
You do know how to terminate Cat6 cable, right?
I've got the safety guards off so we can see what's going on here.
We have an electric motor that has this eccentric rotation
which creates a linear motion down
here and then we have an air cylinder
that provides a downward motion so we have both
a squeezing pressure motion
and a reciprocating motion that untwists the wires.
So then when we load a wire,
those two motions together untwist the pairs.
Gives you nice straight wires that easily take a connector.
Pretty cool right?
So the whole time we were working on that job,
I couldn't help but think about the fact that
the large majority of people that are terminating Cat6 cable
on a daily basis are actually out in the field,
not in an industrial setting.
The biggest drawback of this machine is it requires constant power,
and worst of all, compressed air.
It actually doesn't use that much compressed air.
It's a tiny little cylinder and the pressures are
pretty low. I think we can come up with something
that's quite a bit simpler and doesn't require
dragging around a loud bulky compressor.
All right let's start with power. So the original machine
plugs into 110 but is running off of this DC power brick
and so you can see it takes
120 volts in and it's outputting 24 volts.
Getting a battery that runs 24 volts is a little
bit difficult but I have a ton
of these 20 volt DeWalt batteries lying around and I got one of
these power adapters for a DeWalt battery.
It just clicks right in and allows you to run the
battery to whatever you'd like.
So we're going to try this out and see given that it's a DC motor
I think we can get it running on 20 volts instead
of 24 volts. Next up is air. Now
Like I said that air cylinder is not particularly large
and it's running a pretty low pressure so
what my plan is is to use one of these little bike pumps
and an expansion tank so we're gonna
use the pipe the pump to fill up the expansion tank
so we have a good buffer of air pressure
and then this should be able to keep up
our machine is actually going to run off the air
that's in this tank and then we can periodically top it off
with the pump so that's air.
Now for this switch, so the machine comes with a foot switch
and it's just a two wire switch, pretty simple.
So I
bought
this,
it's kind
of chunky
but I
think we
can mount
that up
onto the
housing
and that's
what we're
going
to use to
fire the
machine.
Alright, well one last little detail here,
we can go try this thing out.
And here we've got our bike
pump, battery adapter,
expansion tank
and our new switch.
Hey Rich, what's up?
Throw a hot battery in it and see what happens.
All right, switch is on,
battery's in.
No smoke, that's a good sign.
Let's turn on the air pump.
Battery's dead,
unbelievable.
Battery's dead, so we're gonna charge that
and then we're gonna try it out.
Okay, we're back.
Air pump battery is fully charged, set to 60 PSI.
Plug everybody back in, let her rip.
Lines were
backwards.
All right, we just hit 60 PSI.
This isn't running at 60 PSI,
but that fills up this tank with some backup air,
so we get quite a few runs out of the one pump session.
So now the moment of truth.
This right here is the activation switch.
We're gonna press it,
and hopefully it'll work just like it's supposed to.
Yes, yes.
All right, it's working just like it was online,
but it is totally not connected to anything.
All right, very cool.
So let's give this a couple tests with some real wires.
All right, we've got a wire stripped here.
Let's give it its first test and see how it runs.
Wow, wow, great.
That 20 volts versus 24 on the motor
doesn't seem to be affecting its ability to straighten out.
This orange wire didn't get all the way done,
but I mean, still, that is awesome.
There's plenty of room to play around and make it perfect,
but I'm really happy with that as a first test.
Well, I gotta say I'm pumped.
After the first couple of bench tests,
this thing is running great.
I think all that's
left is to go test
it out in the field.
Well, field test went awesome, so now I'm here at the job site,
and I want to see, even though we got some of the basics terminated,
there's still quite a lot to do,
so I want to see if this bad boy can't help speed this process up.
So let's get started.
Just got
to get it like that,
maybe like that.
Okay, let's give it a try.
Oh, it doesn't work anymore? What's the deal?
Okay,
straight
wires,
very cool.
Steady, on to the next.
That was a success. Let's roll through
a couple more of these and see how it goes.
Okay, well I've got
a couple cables here
and they're untwisted
and they're
straighter-ish
enough for putting into keystones.
I'd say here at the rack, even though it's a
little weebly wobbly, this is a pretty viable thing.
Maybe if you had a stand
or something it'd be better.
I'm having to run the pump more than I would like. I gotta
an air leak here that needs sorting out
but i'm gonna say overall we're in pretty good shape here
let's uh let's go see how it does on a more difficult
to reach cable. okay well i got a
a uh siren going up there for the alarm system it's poe
so let's see how our rig does something
like that now we
just gotta we just
gotta hold it
and then just
wire wait
a minute i need a
How do you get it? Oh, great. There goes the air. 12 psi.
I need another, I need another hand.
This is a sort of a three hand job.
I'm starting to think that this isn't such a good idea.
I mean, we know the machine works.
I've terminated hundreds of thousands of cables with it,
but it's just, it's too heavy and too awkward to use.
I'm thinking if we spent a little time
just learning more about the machine and how it's working,
we can come up with something that does the same thing,
but is better.
Okay, so if we're going to reverse engineer
this and try to build our own version of it,
we've got to really fundamentally understand how it's working.
So the first...
The mechanic of how this works is the reciprocating motion
of the lower slide, and that one's pretty easy to understand.
We basically have a slide with about an inch of travel going back
and forth in a flat linear motion.
Got it.
Now, the next mechanic we need to understand is this air cylinder.
It's providing the downward force.
Now, the interesting thing about air cylinders is that they provide
a constant downward pressure throughout their travel.
So no matter where they are up and down in their travel,
The pressure that they're applying to a part is the same.
Okay, that's a lot of complication.
What does it mean?
What it means is if we set the device that we're going
to build to clamp the bundle thickness,
we need to make sure that we
also maintain pressure as the bundle gets thinner.
That's the key to why this machine works.
As the bundle, the pairs untwist, the bundle gets smaller.
We're able to still apply the same downward pressure the whole time.
That's the big...
key to this machine working. Now the last thing we have
is there's two rubber pads. The rubber pads give a bit of grip
so that kind of the same way your fingers untwist the wires
they grip onto the wires and
That friction is what causes them to untwist.
So we need to know more about those rubber pads as well.
This is the piece from the original machine.
Now our goal here is to replicate it as closely as we can.
So one of the first things that we need
to know about it is how hard is this rubber?
How squishy, you know, and it's grippiness.
So what we're going to do is actually look for its durometer.
Now durometer in plastics is the measure of how hard a material is.
In metals you have Rockwell hardness.
With wood you have the Janka scale
and we measure durometer of rubber in the shore scale.
What I have here is a durometer gauge
and it's just a tool that has this little pin
on it and when you press it
into a material it tells you how hard it is.
So let's go ahead
and turn this on and we're going to measure the shore hardness of this
piece of rubber.
Okay and in reading this I'm getting 82 and a half.
It's probably not exactly 82 and a half,
it's most likely 80 and we're just have a little bit of error there
but what I'm going to try to
do is find a piece of material here that is both urethane
and 80 degree shore hardness.
Okay this is measuring at 77 so really close
and the blue 85 and our original one was
84.5 so let's go with this blue material
and it feels you can just this is maybe a little slicker
than than the original but I think between one
of these two sheets we'll have a a good workable
rubber pad. Next thing we got to figure out is our method of clamping.
So the original machine uses this air cylinder
and this is what I have in mind. This is a toggle
clamp and this is something that we use all the time
in industrial applications for work holding
and fixturing and things like that.
Now the interesting thing about toggle clamps is that
they work on an over center mechanism
so when they clamp all the way down and click they can't
be lifted back up. That's that's how they work.
Now the thing is is they're adjusted by a
Set screw here so that when you clamp down on a piece of material
and lock them, you can't get the material out.
Now, that would work great in our application
because we want a strong clamping force,
but if you slide in a piece of material that's smaller
and try to clamp that, it just slides right out.
That's not going to work for us.
After thinking about this for a while
and doing some Googling, I came across this.
This is a toggle clamp made by a company called Bessie.
And the interesting thing about this one
is it's got a little spring mechanism in here
that allows it to auto-adjust to whatever it is you're clamping.
With this clamp, it doesn't matter the
thickness of what you're clamping.
It performs its over-center mechanism and locks the part down.
Lift it up, swap something of a different thickness.
It locks that down too.
Now, I don't know how this clamp will do
keeping a constant force over the whole cycle,
but I think because of the spring that's in there,
if we start clamping with a little more pressure
than we would normally, as the wires untwist,
we're gonna still have some pressure
as we finish the cycle,
which I think will be enough to get the job done.
That leaves us with the rubber pad figured out,
a clamp figured out.
Now all we have to do is sort out this reciprocating motion,
and I think I have a pretty cool idea for that.
So this was my first thought. A reciprocating saw reciprocates.
But the thing with this monster is it kind of has all
the same problems as our big machine. It's
heavy, takes two hands, and it's not overly precise.
But it got me thinking.
This is the Milwaukee Hack Saw. It's a M12 battery powered tool.
Fits good in one hand single hand operation
and it has this rigid shoe that we can
sort of use and modify to mount our clamp to and most importantly
it comes with a detailed data sheet instructions
and a breakdown of all the parts.
I think we should dive into taking
this thing apart get some measurements and see if we can't
modify
this to be
the base
of our new
machine.
I think
we've got
everything
we need
and we're
ready to start putting this thing together
so I've got m12 hacksaw and battery.
The blue rubber pad that we talked about,
this has got the same durometer as the original machine,
got some sticky tape to put that down,
some 3D printed parts, of course our clamp,
and this custom aluminum shoe.
I had this laser cut and bent by Send Cut Send. Let's
get
this
thing
put
together
and try
it out.
Last
screw,
now the
platform,
And
there
It is. Needs a little adjusting,
but here we have our new tool.
Here's how it works.
We've got our toggle clamp here with the two adjustment screws
that allow us to set the height
of this upper platform when it's clamped
and then we have another set screw in here
that adjusts the spring tension
and that's what gives us our clamping force.
So you can see we click over center there
and that's providing the clamping pressure.
Now I am noticing that it's not giving quite like I can't lift it up
but it's not giving
quite as much clamping pressure as I had hoped.
I don't know if my heights are off a little bit.
a little bit.
Or the pad's just a little bit thinner than I had planned on.
But we're not getting super tight.
Let's go ahead and throw a part in there.
I've not done any adjustment or anything.
Let's just see what happens.
Okay, it's clamped.
It's tight.
Not even a little bit untwisted.
It's kind of fraying the wires,
which makes me think maybe it is tight enough.
Let's see if we spread them out a little bit,
if it makes any kind of a difference.
Not at all.
Okay, why does this not work then?
I'm almost wondering if these blue pads
are too slippery they are the right durometer but
just in feeling the difference it doesn't have any like grip to it
and I'm wondering if
we need a little more grip out of the pad yeah I
mean I can see that I can see it's tight enough
because it's starting to fray the wire
but there's just no grip so I think let's try switching this
blue pad out for maybe one of the silicone pads
is the way to go it's got more grip I guess we
could try that if it's too grippy we could always dial it back
so maybe we'll switch and try that
I'm almost done switching pads here.
I went back to the silicone rubber that's a 60 durometer,
but I don't know. I just got a good feeling about it.
The other thing is I used a thicker pad here
on the bottom just because I had it to help me get
a little distance back, but we got to readjust here.
I've been doing some testing,
like a lot of testing, and I think we're close.
I've got two different types of wire that I've been working with.
This white wire is Cat6 cable,
but it's copper clad aluminum, which is much softer, much
more malleable, and it's turning out pretty good.
The wires are coming pretty straight.
There's a couple that are still left
a little bit twisted, but they're straight, so I think
we're super close there, but this blue cable, we're not even close.
This is a...
Copper core Cat6A cable. So it's solid 23 gauge copper and it is stiff.
It's I'm really having a hard time getting it untwisted and straight
and to be honest with you even the big machines struggle with this
But we're gonna have to make some adjustments.
I think to get this to work. If you watch when I close the clamp
I'm getting flex right here. You can kind of see that there.
So I think if I redesign this spacer piece to squeeze
this shoe together
We can get rid of that flex, which should help us out.
This'll be the first test with the new clamp.
You can see when I actuate the clamp,
the platform still moves,
but this whole
unit right here
is staying put.
Yes, absolutely perfect.
What a difference.
Wow.
Look, straight wires.
What
do
you
think?
For the solid copper, let's try running the whole thing.
I don't know if that's gonna make a difference.
Yeah, still not really working for the whole thing.
Let's just go back to the individual twisted pairs.
Okay, it's working great for that.
It still had a little bit of a twist to it,
but they're nice and straight,
which is really important.
Definitely don't need to rip it.
Kind of a medium slow is pretty good.
You can actually see the wires straightening
as you're pulling.
So like there, it was starting to straighten,
and then I pulled a little too fast,
and it didn't untwist the end as well.
So there's a little bit of a learning curve,
but you can always just rerun it,
and it's super straight the second time.
If it does it's sort of done pretty good.
I think it's better than doing it by hand.
I think for this one, let's skip the field test
and just head straight back to the job site.
Last time we were here,
we needed three hands to terminate this cable,
but let's see with our new tool,
if we can get it done with just
the two we got built in.
So this is that solid core wire.
So I'm just gonna
do one at a time.
Beautiful, easy to open
and close the clamp with one hand.
Nice,
four straight
pairs,
not bad for the first on the job test.
Let's see how they terminate.
Orange, white, orange.
They're already super straight,
but I'm gonna trim
the ends flush, angle,
leave a thousand wires on the ground,
and straight in, nice.
Super easy, super smooth.
All that's left to do is screw.
Never see that again.
Right, there's our first one
with the new tool, cool.
We're back at the rack with our new machine
and a bag of keystones.
Let's
get
the
rest
of
this
panel
terminated.
Back is done.
I've really been procrastinating that while I've
been working on this tool, so I'm glad
to finally have it finished up.
And our tool did great. I was pretty bummed out
when I couldn't get it to untwist the full bundle at one time,
but honestly, going twisted pair
by twisted pair is really not that bad.
This thing is so reliable
when it's doing just one twisted pair of that Cat6a
that it just doesn't make that big of a difference.
And it rips through Cat5 and that softer Cat6.
Both of them I haven't had any problems at all with.
To be honest, I'm a manufacturing and software guy,
not an IT professional.
I'd really be interested to know if any
of you guys that work in this trade and terminate
Cat6 all the time, is this something you'd use every day?
Does this seem like a tool that's practical
or did I spend a hundred hours engineering
the solution to a problem that doesn't exist?
Either way, drop a comment down below
and let me know what you think of the tool.
I understand I probably should have done it the hard way
and built up calluses and whatever,
but this is a fun way to procrastinate.
And I enjoyed building this machine right here.
About as much as my four-year-old.
It did work.
I mean, I think it kind of proved the concept,
and I'm glad we had a chance to play with that.
Thanks so much for watching, and I'll catch you on the next one.
