We're finally starting to plank the Poulsbo Boat Project. The inwales and thwart risers are shaped, the cedar strips are ready, and it's time to start turning the moulds into a hull.
There are a few things to prepare before the first plank goes on. I'm masking off the inwales and thwart risers so I can remove them later for interior fairing and fibreglassing. I'm also scarfing the planking stock with a new jig I made to hold pairs of strips securely while I cut the joints.
The real challenge begins when I start fitting the planks. This hull has a lot more shape and twist than the canoe-style strip-building process I'm familiar with. I started at the sheer and worked towards the keel, but I'm quickly discovering that a beamier hull needs a different approach to establishing the plank runs.
Steaming helps get the cedar into shape, but it isn't the whole answer. I'm experimenting with back bevels and tapers to make the planks wind into position, and learning as I go. I also make some changes to the steam box setup and rethink my choice of fasteners after finding that the two-inch brads are occasionally coming through the planking.
This is very much a case of working through the problems as they arise. There are things I would do differently if I were starting over, but each step is teaching me something about strip-building a hull with this much shape.
**In this episode:** - Preparing the inwales and thwart risers for removal - Building and using a scarfing jig - Scarfing cedar-strip planking stock - Why this hull needs steamed planks - Setting up a longer steam box - Fitting the first planks and managing twist - Using back bevels and tapers to control plank shape - Changing fasteners to shorter crown staples
The Poulsbo boat is a modern cedar-strip interpretation of a 1950s-era sport fishing boat originally built by Ronald Young in Poulsbo, Washington, using traditional carvel construction. We're building this version with cedar strip and fibreglass inside and out.
If you enjoy following the process, including the experiments, mistakes and solutions along the way, consider supporting the channel. Join me on Patreon.
Thanks for watching, and I'll see you in the next episode.
0:00 The challenge of strip-building this hull 0:15 Back to the Poulsbo Boat Project 0:41 Preparing the inwales and thwart risers 1:14 Masking off the members before planking 2:17 Making a new scarfing jig 3:09 Keeping track of the planking stock 4:38 Gluing the scarf joints 5:09 Using Mylar to separate the strips 5:51 A steady scarfing routine 6:47 Why this hull needs steamed planks 7:20 A lesson in choosing the right planking approach 7:51 Finding a neutral plank line 9:02 Improving the steam-box setup 10:07 The first planks go on 10:50 Managing the twist at the bow and stern 11:30 Extending the steam box 12:05 How long to steam the planks 12:59 Changing the steam-box orientation 14:22 Getting the longer steam box running 15:53 Dampening the planks before steaming 16:27 Protecting the clamp pads 17:42 Preparing clamps before fitting a hot plank 18:33 Working out how to hold the plank in place 20:41 The first signs of trouble 21:00 Why the bow planks aren't fitting 23:52 Using back bevels and tapers to control twist 25:28 An experiment that works 26:07 Shaping the planks to fit 30:13 A new day in the shop 30:30 The challenges of fitting the planks 31:05 Changing from brads to crown staples 32:40 Why I'm using stainless fasteners 34:01 Would carvel construction have been easier? 34:18 Live and learn
AI Generated·May contain errors
Have I mentioned that I have no idea what I'm doing here?
If I had known how challenging it
was going to be to try and strip build this hull,
I think I probably just would have gone
with the traditional Carvel construction
that these boats were usually built with.
Hey folks, welcome to Nomad Boat Building.
We're picking up where we left off on the
Poulsbo boat project. The Poulsbo boat
was a popular sport fishing boat built by Ronald
Young in the Poulsbo, Washington area.
Ronald built his using traditional Carvel planked
construction. We're building ours using
a modern cedar strip construction, fiberglassed inside and
out. In our last episode,
we finished shaping the inwales and thwart risers and now we are
ready for planking. Now I'm doing something
a little bit weird in this particular build in which
I'm not going to be gluing the planking
to these members right away. I'm going to
remove them and then reinstall them later on.
And that's because I want to fiberglass on the
inside of the hull and I'd rather not have
these in the way of that fiberglassing process. I feel
like that would make the fairing
and fiberglassing process a lot harder if those were in place.
But I do want to get them shaped ahead of time
because it's easier to do that now on the mold
than it is to do it later on in the bare hull.
What I'm going to do today is I'm going to
Just get all the...
The sawdust off of here, I'm going to do a little cleanup
on these inwales before I go and start with my planking.
And then I'm going to tape off both the thwart riser
and the inwale with some masking tape
so that I don't glue my planking to those members.
Because remember, I want to pull those out.
I could use packing tape for that, but what I've discovered
with packing tape is while it's a great material to prevent...
Epoxy from sticking. It is a pain in the ass to get off
of things that once it's been on there for a while,
and especially if pressure has been applied.
And so for that reason, I'm just going
to make life easier on myself and use masking tape.
Some of it may stick to the planking
and get peeled off when I pull these out,
but that's not a big deal because it'll all clean up pretty easily.
It is just paper after all.
Now, one of the things I could do to make that less likely
to stick to my planking is I might just give it a coat of...
furniture wax because that will do a beautiful job
of making it stick free. stick free? sticky? non-sticky?
non-stick cert... i don't have the word for that. so i've got
a pile of my planking stock that i need
to scarf and i didn't scarf it ahead of time before ripping
because i decided it was going to
be more effort to try and cut scarves on wide panels
and glue them all up because i know i'm
going to need some variation in lengths
a little bit. i just don't have enough volume of planking
planking on hand, it just...
Make a ton of extra. I sort of got barely enough.
Anyway, to facilitate scarfing, I've made a new
scarfing jig here. And the idea is I can put two pairs
of planking into this slot and use this
hold down to clamp them in place and then quickly run the scarf.
So I've got some of my planking
stock right here. And what I've been doing
is taping pieces together in pairs, just at one end,
just to help facilitate the scarfing process.
I'm doing this in pairs because it just helps me to,
as I'm working, to keep track of whether
or not I've got enough for the whole boat.
I swear I have some unspecified form of dyslexia
in which when I have doubles, multiples of things,
I suddenly get confused about how many I need.
And I've often found myself going through
a whole milling process of something
only to discover I only made half as many parts as I required.
So this is just a way of
Making sure I don't screw that up.
Everything's done in twos and I need enough both sides of the boat.
I'm gluing
to glue
these up
with
Titebond
3.
While any
sort of
adhesive
would
do the job,
and certainly epoxy would be the most robust,
Titebond 3 offers simplicity, flexibility,
and in fact it actually tolerates steaming
relatively well. And since I'm going to be
gluing these scarfs up one pair at a time I just want
the simplest possible adhesive to use.
I'm preventing my two planks from sticking together
by using these little pieces of mylar bent into an L shape
and trimmed down to the same size as the planking.
I've never really tried using mylar in this way before,
but I'm finding it really effective for this particular application.
I'm going to be doing this again in the future.
While this might seem like
a slow and tedious process,
in fact I'm quite enjoying it.
It gives me a break
from the other activities
in the shop.
And I'm able to glue up, I don't know, three or four of these a day.
I usually give them about an hour
in between them for them to set up properly.
And if I'm staying one day ahead
of the planking routine, that's fine by me.
Clamp everything up with some cauls that are fitted to the planking
and covered with a bit of packing tape.
While strip
building
generally doesn't
involve steaming
your planks,
this particular
boat demands it.
There's just so much shape to the sheer.
As I said before, I'm new to strip building
and so I decided to follow the process that one would
normally follow for strip building a canoe, for instance.
You start at the sheer and you work
away to the keel.
Well, that was probably not the best plan as I'm going to discover.
But that decision was made and now I'm just going
to move ahead blissfully ignorant of the troubles
that are going to lie ahead of me.
Now this is one of those times that I'm going to have to admit
I have to admit that my experience has done me a dirty.
I figured how hard could this be?
I've read Ted Moore's strip building book.
I've seen enough boats strip built
that I figured this is going to be a cakewalk.
But what I didn't bother doing was reading any other books
on the subject or really doing any
research into strip building beamier boats.
And that is going to prove to be my undoing.
When strip building beamier boats,
usually you start by finding a path for the planking
that is neutral to the shape of the hull,
somewhere about midships, and then work
up and down from that particular path.
This is a practice that's actually pretty common in
larger boat construction,
where you lay out a line you call the magic line, and that is
a line that wraps around the boat
that represents the straight edge of a plank.
And you develop your plank shapes from that above and below.
I just didn't do that here.
I just thought, let's follow the sheer line like we do with canoes.
It'll be fine.
And I had some thoughts about the fact
that this sheer line had so much shape
that I wanted these planks to follow along it
and not be running off at some weird angle.
Well, that was a dumb premise, and I will learn that the hard way.
But you know what?
I'll also learn a few other things along the way.
It's not all wasted effort, in my opinion.
Sometimes you gotta do things wrong to learn how to do things right.
That first round of planking I'd steamed in two halves,
one steam operation for the back, one for the front.
That was kind of inefficient,
so I thought I'd set up a longer steam box and do it all in one shot.
I'm using these little plywood brackets to help control the planks
as I pull them out of the steam box
and try and set them up on the hull,
because they're long and skinny, hard to handle by yourself.
And we got our first couple planks on.
The first plank I tacked on with the pin nailer, the plastic nails.
I just got like a single screw
holding it here where it's got the most twist to try
and tease it into place. And then the next one
is just glued to the first one. It's not tacked in any way.
Now I'm going to be edge nailing all
the planking, but I didn't want to do the first one
because I wanted to make sure this first
First plank, those free and clear of nails
so that I can fair out the shear when I start to.
put the boat and clean it all up
because you need a little bit of wiggle room for that.
And so I've steamed these planks into place
which seems to be necessary because of the
bulk, the amount of shape in the bow
and the amount of twist in the aft run. There's quite
a bit of quite a bit of twist in here.
I think it's going to mellow out pretty quickly but for
the time being for the next half dozen planks I think
at the very least I'm going to have to
keep steaming. You have to get fairly elaborate
with clamping to get the twist and
bend in there these forward sections.
Once I start nailing I don't think I'm going to need to do that.
So I had the steam box set up here with my regular section of pipe
but to steam the whole plank I
ended up adding like this piece of gutter downspout
that I had kicking around. Now I've
got a longer 16 foot wooden box
which I might just set up today so this was a bit awkward
being in here. So I think it's a nice day outside.
I think I'll set it up outside.
Maybe get the wooden box going,
then I can drop more than one plank in at a time.
I need about these planks,
I'm giving them about 15 minutes in the steam.
That seems to be about right.
One thing I've noticed, now I've always in practice put the
the end that I want to have the most shape into of a plank,
I've always put that near the steam
generation end of the box.
And that's always worked out fine, but you know what I noticed
One thing you'll notice this time around and that is that the tail end
The part that's near the exit of the box is always,
it's the wetter end of the box
because the heat's coming from the other end.
The water is condensing more by the time you get up here.
It's still hot, but it's decidedly wetter.
And I noticed when I was bending these in,
this forward end here was quite dry
as I'm driving it in, whereas the back end,
you could feel it was quite a bit wetter.
And I think I want the wetter end up here, frankly.
So what I'm gonna do is,
Move the box outside so that the tail end that's going to end up here
is at the wet end of the box and the dry end is out there.
So for that reason, having the box outside makes more sense.
So we'll do that.
I'm going to break down these clamps.
I'm going to set up the box.
I should set up the box first so it's getting up to heat.
So let's go do that.
All
right,
we've
got
the
box
up
and
rolling.
Just using the one
One cooker on here, the 220.
So this box is two pieces, so I can use the one piece on its own,
or I just add this extension to it when I want really long stuff.
And it looks like my longest
pieces don't quite make it into the box, a couple inches short.
So we'll have to towel up the end
for some of this stock. We'll see how it goes.
That box is going to take a little while to get up to steam
I want to probably give it at least a solid half hour
of cooking before I call it ready to go,
because it takes time for the steam
to start absorbing into the plywood of the box
to get it all nice and damp up in there.
Ideally, we just want a really nice damp environment
for these things to cook in.
And I might just go ahead
and mop down these first pieces just to get them a little more supple,
Obviously we don't want them soaking wet for
Going into a strip-built boat, but I mean there'll be tons
of time for it to dry out before glass is going on.
So maybe I'll grab a towel,
mop those down, take care of clamps,
and then figure out what to do
with myself while that's coming up to heat.
Be surprised how dampening the surface really helps
things steam. Like it's not like it's soaked
or anything like that by a long shot, but just that
that surface water tends to really help
the steam penetrate a bit better. Not too sure why.
So I had this thought
and that is I'm going to be using a lot of my small
F-body clamps for doing the clamping
on this as I'm nailing things together. They've got little
leather pads on them which I'd rather not mess up with a pile of glue
so I had an idea to suddenly
put a little masking tape on that pad so that it stays nice and clean.
I'll just pull it off at the
end of the day. These particular clamps are kind of nice
but a lot of them came without a plastic
cap on the um on the business end like they put a cap on the screw end
but for some reason they
didn't put any on the business end um which isn't a big deal
because those things tend to fall off
anyway so i put leather pads on them
which makes them infinitely better in fact i think all the
clamps i have i prefer that have leather pads
on them as opposed to the plastic
But of course, they're susceptible to getting glue on them,
whereas the plastic ones, especially on my quick grips, are nice and,
you know, you can get glue on them and peel them off pretty easily.
And in fact, I even sand these down every now and then to get rid
of the glazing from the glue so they get a bit grippier.
Anyhow, so that was just one thought I had.
Another good prep work thing you can
do is staging clamps where you think you're going to need them.
Before I have a...
The thing coming out of the steam box,
it's all hot and steamy and you want to get it in place quickly.
You want to make sure that your clamps are sitting where you need them.
Even if you just have a handful that are quick to grab.
So we've got some of these little f-bodies kicking around.
We'll have some quick grips ready to go.
Of course you want to make sure
that they're opened enough that you don't have
tons of squeezing to do in order to get them deployed.
But you also don't want them getting
in the way where you want to hang the plank.
All of these little things can be thought of in advance.
So one thing that has been useful is having the tail end of the plank
controlled while I get the other end of the plank in place.
And these little guys were doing well
for that but now they are not going to be
quite as useful for that because of the configuration.
So maybe we'll go like this with one of my L-shaped ones.
So the idea is I quickly come in here,
I slip the plank through, get it fitted down at the bow end,
and then go back and fit the aft end.
And so to facilitate that, I want to make sure one end
isn't falling onto the floor.
So I can just slide it through here, this little clamp, and
that should be good. I suppose I could do it this way.
Yeah, maybe this way. That might work okay.
We'll find
out. Okay,
things I
didn't
anticipate
exactly.
There's a certain amount of twist I've got
to figure out how to impose on these guys,
which is not immediately apparent.
Well, I'm going to have to do some beveling, probably.
Let's just worry about getting the shape.
Come back and worry about beveling.
I'm only three planks in here,
and I'm already not liking how these are fitting.
Most of it's fine, but up here at the bow,
they're giving me a real fight.
The bulk of the trouble happens roughly around the second mold there,
where the plank really wants to tip itself out.
It was supposed to lie against the mold.
While I can wrestle it into place with clamps and or
screws, I don't think this is a long-term solution
for the rest of the planking process
because what I don't want to do is screw this thing
to a mold all the way along only to have
to remove those screws in order to do the fairing process
and perhaps it starts moving on me and
popping open. I don't know.
I don't know what'll happen but I don't like the idea of it.
I do know steam alone isn't going to get these into the right shape,
and so I have a couple tricks up my sleeve I can try.
Steamy!
Just give
it five.
Okay, what I
did just here
is I did a
little bit of
doctoring up
on this plank.
I put a bit of a back bevel on through this section right here,
but then I also tapered the bottom off
to about half the thickness down here,
and what that does is it has the effect of
Causing the plank to wind
in but you wouldn't think it makes a difference
It's not the same as if I just took the top edge off
because it's basically there's a crown on this and that's that crown
Goes down and it forces this guy to wind in a little bit
when you take a thing
That's on edge and you you can over bend it.
It's really hard to explain. It's hard to even demonstrate but
Here so this is sitting like this as I bend it down as I force it down.
You have to look back here
You can see that this top edge wanting to bury itself
and the bottom edge starts to starts to
wind out. So that's what I'm doing.
I'm forcing it to do that which is exactly the shape I want to
take in here. So it seems like a subtle thing but it works.
So if I wanted the opposite, if I wanted
I wanted it to flare.
I would do this. So back here,
back at the transom for instance, if we wanted to flare up,
it would make sense if I added a little stealer plank
so it forced the next one to
swing up a little bit and I would get twist.
That's sort of the one of the little secrets
of learning how to manipulate planks.
You only learn that stuff usually by experimentation.
So I think that works pretty good.
If I take my existing plank and I do a little doctoring up to it,
I should get it to sit down where I want it now.
But my experiment was successful, I'd say, so that's great.
So what did I reduce this down to?
A half inch?
Yeah, about a half inch, but not thickness.
The question is whether or not I've got
to keep doing that for the first few planks.
We'll see.
I think it's going to start to mellow out as I get a bit higher.
Until the shape mellows out,
we're just going to have to keep with our tapering and beveling.
Luckily my slick makes short work out of the tapering, and this red
cedar is so soft and workable that beveling is no big deal either.
Actually,
I
kind
of
enjoy
this
sort
of
stuff.
Ha! Knees back.
Leaving
these just to
hair proud and
just flush them
all up after.
Yesterday
was a
reasonably
good
day. I
didn't
really
get
quite
as
long
a day
in
as I
wanted,
but planking is coming along and I've learned a few things for sure.
One of them is that there's a lot of shape in this boat
and it is proving challenging to try
and get these planks in place.
It's not just a question of dropping a strip on here and nailing
it on. I need to carefully put some bevels on parts
of it in order to get it to sort of conform.
But then there's a lot of coercion to try and get it to tip into place.
It's like fighting.
It wants to be plumb here, plumb there,
tipped in here and it doesn't really want to do that
very effectively.
I've also been nailing with this 16 gauge brad nailer,
or finish nailer, whatever you
want to call it.
And it's kind of big and clunky
and I'm using 2 inch nails which every now and then are
popping through.
So I'm gonna have a bunch of patching up to do where I gotta
Trim those nails off and get them below the surface of the wood to fair
it out, which is going to be, well, it's not going to be too bad.
There's not a ton of them,
but trying to drive them out is really difficult.
I mean, the odd one that's on the outside, I can sort of do it,
but when they're on the inside, I can't get enough swing to budge them.
I went out today to try and get some shorter nails
because the two inch, you know, is long
enough that it's like it's too easy for it
to suddenly go off in a weird direction.
And I couldn't get shorter ones in stainless in that size,
but I was able to find shorter ones in
quarter-inch crown staples. So I'm going to switch to those.
They're only 18 gauge, but there's two,
right? So it should have the same holding power,
if not better, especially because they're crown
staples. And my crown stapler is a lot leaner
and easier to sort of fit into tight spaces,
so I think I'll have an easier time
of nailing these together using that.
So that will hopefully be an improvement.
Um...
I don't know if I really needed the heavier nails,
but it seemed like a good idea at the time.
So I just wanted to say something about nailing these things together.
I mean I could probably get away
with not using stainless nails, but it seems like a good idea.
Now this is an encapsulated hull which means it's gonna be glassed
inside and out and any penetrations are gonna get sealed with epoxy.
So the goal is that this whole hull never gets any water
into that core material.
To that end you can generally get away
with using you know fairly junky wood for strip building.
You could even use stuff that's highly rot prone
because it's supposed to stay isolated.
Now that doesn't always work out.
I mean as you know with like balsa core boats they
develop leaks every now and then you get rotting balsa core.
It's not necessarily a huge deal
because if you're starting to get rot in the core you got
bigger problems. But you know I like
to do my best to try and keep it as
rot resistant as possible.
It's like I mean there's one plank here
that's got a little bit of sapwood in it.
It's buried so deep in here that I mean any rot problems
are likely to happen along the shear line.
In fact looking at this I kind of wished I'd used
this cedar down here at the shear instead
of that cedar that I used
but because this feels like it's an older growth cedar.
I can tell just by looking at it but anyhow no matter it is what it is.
If I had known how challenging it was going to be to try
and strip-built this hull,
I think I probably just would have gone
with the traditional Carvel construction
that these boats were usually built with.
I swear, I would have been further along in the planking process
if I were building in Carvel right now than with strip.
But...
Live and learn, right?
Alright folks, that's all I've got for you this week.
I hope you join me again when I either make
some more mistakes or maybe come up with some
new ideas to fix my old mistakes.
I don't know, I haven't cut the video yet,
but you can be the first one on your block
to find out when you watch the next episode
of Building the Pulsebowl Boat.
Now if you enjoyed these videos
and would like to help support the channel, please consider
joining me over on Patreon.
You can find links in the corner or down in the description.
Alright folks, that's it for today, I'll catch you later.