I Borrowed It. I Broke It. Now I Have to Fix It. Why is it that breaking your own equipment is just frustrating, but breaking someone else's equipment is devastating? I waited too long to complete this relatively easy repair and mentally beat myself up until it got done. Anyway, I don't plan on borrowing equipment any time soon.
PPO3 is supported by Timber King sawmills.
For more information on my 1220 CRZ mill,
or one of many Foley hydraulic options, go to TimberKing.com.
Quick note about the heater. Somebody called me out on this and said
that my pipe is installed backwards, and I thought, no it's not.
I've installed many dust collection systems
and water piping and airflow piping and I understand
that the mail end goes away from the airflow
as the airflow goes through the pipe.
You don't want it to have that gap to go out
of as it's going through the pipe.
It's not wrong. Well, I was wrong. Yes, it is wrong. I looked it up.
And I've never worked with wood burning stoves before,
but I've never installed one.
So the conventional thought of having the mail side away
from the airflow is actually wrong on this interior stovepipe
and actually all the whole run of the stovepipe.
Whether it's stovepipe in here
or like the Class A chimney pipe outside,
you want to have the male side facing down
which is kind of sort of counterintuitive.
But the thing I didn't take into consideration
is as condensation happens inside the pipe with
the creosote, if that turns into a liquid
and starts running down the pipe, if the male side
is up, then it can go through that seam
and come outside of the pipe which can cause all
kinds of fun problems. I did not know that.
Thank you for pointing that out. So I did swap this around.
All the mail sides are now facing
down and the more you know. I just got back
from a parts run a little ways away and I had to get
the stuff to get this disc repaired.
Remember that disc that I tore up that I borrowed,
I don't know, summertime, late summertime?
I should have taken it off. Hung a tree and bent
this axle right here. So it's bent quite a bit.
I don't know how much it's showing up but it's
It is bent a considerable amount,
so we gotta buy some parts.
Well, I'm just now getting time to,
not time, but getting around to repairing it.
This is the axle shaft, and it was bent considerably,
but I took it to a machine shop, not a machine shop,
a welding shop, and they were able to
actually straighten it out without putting any heat in it.
So yay for that! 20 bucks to have
to have this straightened out, that's awesome.
So the way that this works is.
This doodad, I don't know what the terminology is on all this stuff,
but this slides over the shaft, and it's a square shaft,
well that's a square hole, so this rotates with the shaft.
This bearing block, grease block, I guess this would be the bearing,
this would be the grease block, this is split.
And there we go. And you see the grooves in there?
They line up with the grooves right here,
and there's two grease fittings on this thing.
You just pump it full of grease,
and it's, other than the grease,
it's just a metal on metal containment system.
So that the shaft with this capture can spin
with the discs that are captured on this,
and the grease provides the lubrication. The more you know, once again.
So it was kind of a pain in the butt to take it off. I had to cut
two of the bolts off
because the carriage bolts inside stripped out a little bit.
Anyway, what had broke when it bent, obviously it did bend, but this
Bearing block. No, that one's still good.
Where's the bad one? Oh, the bad one is underneath this
rag. So the bad one where it broke was the end of it and the,
uh, the bend in the axle just
snapped that, snapped that off right there.
So when this first happened, I was like, oh man, I
I broke something that's not mine, it was borrowed,
which still sucks, but I was thinking
that this was going to be like a $200 repair,
I looked it up online, parts and whatnot,
I'm like, oh my goodness, and then my uncle,
who this belongs to, said, no rush, just whenever
you can get around to it, he doesn't need it anymore
this season, so no rush, which
is kind of sort of the wrong thing to tell me,
because if it's no rush, then there's
always something else that's going to take priority.
So here we are, a couple months later, and I'm
finally getting around to repairing it.
Uh, but this just disassembled pretty easily,
it should be put together pretty darn easily as well.
No damage at all to the discs.
All right, axle shaft, big washer, end cap,
doodad, thingamajig, all the way by the bottom.
Spacer. No, no, no, not spacer yet.
We need the first disc. That's a lovely sound.
Now we put the spacer with the small end facing
the concave side of the disc.
Then one more disc.
Bearing block.
With the small end on the concave side,
which means the big end goes on the convex
side of the next disc. The spacer
with the small end facing the concave side,
followed by the next disc.
I need an extra hand. Followed
by the bearing block thingy.
Then we have this.
Wash, no, no, no, no.
I'll get it right.
Then...
The big locking washer, that's not a locking washer,
that is a washer that, I don't know
what that is, it's a washer thing that captures the shaft,
then a lock washer, and then a
big ol' nut.
Screw that on there.
And then once I get this, before I get this tight,
I set it down and go look at the other
one to make sure that I did this right.
Alright, axle, end cap, thingy, with a thingy,
followed by a thingy, other thingy, that thing.
Those things go on top of that thing,
then that thing goes there, spacer, thingy, thing
and thing and thing.
Well, I think we're good.
Oh, that's a lovely sound.
This tightening method
is the Binford Foot Stomper 3000.
I don't have a cheater pipe that fits over
the only adjustable wrench that I have that
7 inch wide nut. Now you may be thinking,
how tight does this need to be?
And to that I'll say, I don't know.
But I'm using one foot pound
or something like that.
And the lock washer is compressed.
So that's tight enough.
Okay, the tag on the part I replaced said
that this is a ribbed disc spool.
Uh, 2349, so.
$23.49 for this part
and then 20 bucks to have the axle straightened out.
And I was expecting this to be like 150-200 bucks so I win.
No no
no no
rain
yet.
Stop
raining.
You're
not
supposed
to
rain.
Rain rain go away. Please wait another half hour.
All right we're in business. Greasing this side
and right there. I just drove off with the camera
But all fixed.
Spinning like every other one of them is,
so time to return this and never borrow it again.