Today I'm building a breakfast nook for our kitchen - a project that's been on my wife's list for some time. There are a million ways to build these - we opted for a more minimalist modern look that fit the aesthetic of our kitchen.
🌳 MATERIALS 5 x 2 x 4's 1 x 1/2" x 4' x 8' Furniture Grade Plywood 1 x 3/4" 2' x 4' Furniture Grade Plywood Wood Screws Brad Nails Pocket hole Screws Wood Glue
📲 Check me out on SOCIAL MEDIA! INSTAGRAM: instagram.com/workshopedits FACEBOOK: facebook.com/workshopedits
Zach
What's going on everybody? I'm Zach and welcome back to Workshop Edits. In today's project I want
to take you through how I built our breakfast nook. Let's go ahead and get started. All right,
so we are in the shop. I have all the materials that I need for the project. We are going to head
over to the table saw and start breaking things down. That's going to include the plywood,
which is going to make up the top of the breakfast nook, as well as the bottom supports, as well as
the two by fours, which are going to make up the framing for it. So let's go ahead and get started.
So the framing of the breakfast nook is built entirely from two by fours. Super easy, but I
don't want it to be three and a half inches tall. I think that's going to look too bulky in our
space. So what I'm going to do now is just rip the rounded edge off of one side of each of the
two by fours that I have, flip them over, and then rip off the other rounded edge to a final width
of two and a half inches. Then we can get on to framing this thing out. So let's go ahead and do
that now. All right, so everything is cut to its final length and width and we are ready to begin
assembly. So I have these cross supports to go along with the two individual long pieces for
each of the boxes that I'm building. I'm just going to clamp everything up and then pre-drill
some holes and then drive in some screws. And it should be relatively straightforward. I'm
basically just building two boxes. Okay, so everything is assembled. I also pulled together
the two boxes to make the L. And what I also wanted to do was bring it inside to the space
just to make sure that it fits. Sometimes walls aren't exactly 90 degrees. Mine definitely aren't,
but not out of 90 degrees enough that this isn't going to fit there. It was also helpful because
I was able to mark out all of the stud locations and figure out if any of these lateral supports
needed to be shifted over for whatever reason because I wouldn't be able to drive a screw in.
So I need to actually move a few of them. I'm going to do that right now.
Okay, so any of the cross supports that were interfering with stud locations have been moved.
All the holes are pre-drilled and I drove in some big 3.5 inch screws into all those holes.
I think I want to mount this next because I think it's going to be easier to cut the
plywood to its final size once this thing is in place. And I also cut some big 4x4 14.5 inch
spacers because that's going to be the height of this bench from the ground. That way I can put
these in strategic locations and set this on top of it and then check for level and then drive in
those screws. And I also think it's going to be a lot easier to mount this thing from the top and
not have the plywood in the way. So I'm going to go ahead and do that. And if for whatever reason
my stud locations are off, then I'm just going to repeat that process of finding the studs,
pre-drilling holes, and driving those screws back in. Okay, so just finished installing the frame
of the bench. It feels really secure. I wouldn't sit on it without those 4x4 supports in there for
now. And eventually I'm going to add some actual decorated supports in there. But it's secure into
the wall. It's good to go for now. The next thing I did was bring in the plywood and actually set it
on both of the framing structures just to make sure that it fit. And I was able to mark out
exactly the length that I'm going to need to cut it now, which was really helpful. I also noticed
that because it's not exactly 90 degrees, I'm going to have to notch just a tiny angle on the longer
piece just so those two will sit up flush to each other. I'm going to cut these to their final size.
Then we're going to head back into the kitchen and we're going to fasten them to the bench top
just using brad nails. I don't want to glue these in place if for whatever reason I have to change
them out or I need to modify something after, you know, using this thing for a couple of weeks.
There's no way I'm going to be able to remove them if I glue them down. And brad nails is going to
hold it down totally fine. All right, so the bench tops are installed. Those are just placed on top
of the framing and I secured it using a bunch of brad nails just all over the place. I'll go back
later and fill those in with some wood filler before painting. This is a really complicated
project. Let me take that back. This is a really simple project, but it's actually really complicated
because you just need everything to line up perfectly and walls aren't straight. So it's just
been a lot of back and forth between the house and the shop just to figure out and get things
right and it's still not perfect. So the last thing I'm going to do is take the remaining plywood
and cut strips that are going to go on the front of the bench and it's just going to hide the
framing of the structure. I haven't decided yet if I'm going to round over the bottom parts of
it to make it a little bit smoother or I'm just going to keep it as is. But for now we're just
going to cut the strips at the table saw and then install those as well. All right, so we just
finished installing the bench top. I used a flush trim bit just to get all of the plywood exactly
flush to the front of the bench. In reality that probably would have been easier to do in the shop,
but once I had it mounted I didn't want to take it off and it wasn't a big deal. It just made a
little bit of mess in the house which meant I had to clean that up. Now what we're going to do is
turn our attention to the supports of the bench. So we went through a lot of different design
options for this whether we wanted to have a floating appearance or we wanted the entire
bottom to be covered so that you couldn't get access to underneath it or if we wanted to have
drawers down there for whatever reason. But since there's a kitchen table there it's just going to
be kind of weird. What we ended up landing on was a pretty simple design that has two outside pieces
that are kind of angled and then a box kind of square shape in the back corner. That way you
have support in the back corner and on the outsides and it's going to be plenty strong
enough with it anchored to the wall and having those supports underneath it. All right, so let
me catch you up on everything that I just finished doing. All of the support pieces are cut to their
final length and width at the table saw. I also used the table saw blade just slightly raised up
to route a couple of grooves on the outside supports. I think aesthetically it just adds a
little bit. It was a design that my wife and I landed on. The middle support which is just a box
with mitered corners is built around a couple of scrap 4x4s that I have. That's solid and
assembled and good to go. I'm not actually going to even mount that from the underside. I'm just
going to slide it in. It's such a tight fit that I don't even think I need to and for whatever
reason it does shift over time. No big deal. I can just add a couple of screws but I think it's
going to work out really good. So the next thing that I want to do is take the two outside support
pieces and drill some pocket hole screws on the upper inside edge because we're going to use
pocket hole screws to attach it to the framing that we already installed. The other thing is I
need to take a couple of extra 2x4 pieces and mount them on the under inside of the framing
using just some screws because I want to have more lateral space for those supports to mount to.
All right so we are now ready for final assembly. So what I'm going to do is take
the outside support pieces which are totally good to go. They've got their pocket holes pre-drilled
in them. I'm going to take the middle support bring that inside and slide it into place and
just leave it there. It's going to be good to go. The last thing I'm going to have to do is because
our walls have baseboards along the edge and I don't want to spend a bunch of time scribing on
the bottom back outside support pieces so I'm just going to take those pieces line them up exactly
where I want to mount them and then use my multi-tool which I never use but man when when it
when you need to use it it really comes in handy and I'm just going to notch out spaces so that
those boards can slide directly up against the wall. It's going to look really nice and clean
and flush. For whatever reason I mess up you can always just add a little bit of paint and touch
up those places but I think it's going to work out really good it's going to look really clean.
Once those pieces are notched out I'm just going to use my speed square to line it up
make sure everything is vertical perpendicular from the ground and from the wall then we're
going to drive in those pocket hole screws and it should be really strong. Once everything is
mounted and screwed into place this thing is going to be ready for paint so we can go ahead and do
that. All right so that is going to wrap it up for this project. I hope you guys enjoyed it.
This is just part one of us redoing this kitchen area. We are also going to be building a new
kitchen table that's going to fit the space a lot better. Overall really happy, hi, really happy
with how this build came out. I think it's super clean, modern, fits the space really well. Harley
clearly loves it so yeah if you enjoyed it I'd love it if you would subscribe to the channel
hit that like button and I will see you guys next time on whatever it is that I'm building. Bye.
Do you like the breakfast nook? Oh thank you, thank you, sweet girl.