Super Simple CNC Table Onefinity X-50 Woodworker Easy Workbench

The Stone Cube
31 followers
18 Video Views·Nov 3, 2022
Super Simple CNC Table Onefinity X-50 Woodworker Easy Workbench
So, this build is just about as easy as it gets. The entire thing is constructed of 2x4s,
a sheet of 3 quarter inch plywood, and some screws to connect it all.
In here, I forgot to hook up the second dust hose, so that's why you see a bunch of sawdust
coming out the front. And while I clean that up, let me show you the basic idea of this workbench.
You can see that this is very simple, and if I remove the top surface,
I'm left with a top frame, a bottom frame, and four legs connecting the two.
So with that, let's get started on the top frame. And I should also mention that this
is almost identical to my outfeed table slash main workbench that I built a few years ago.
Also, Bruce Ulrich recently built a table for his CNC that's very similar,
so go check out his video after you're done watching mine.
I started with the outermost pieces of the frame to make a box.
For all these connections, I'm pre-drilling with a countersink bit,
and then driving in some 2.5 inch screws. And I'll be sure to leave links for all
tools and materials that I used for this build in the description box below,
so if you're curious, go check those out. And I will mention, those are affiliate links,
which means that if you click on them and make a purchase through them,
I earn a small commission, but it doesn't cost you anything extra.
So if you choose to help me out in that way, you are awesome, and I really appreciate it.
Once the outer frame was put together, I evenly marked out where the center supports would go,
and installed those as well. Now, pre-drilling isn't entirely necessary here,
because the wood isn't likely to split like it would at the end of the board,
but I did it anyways. It's just nice to have the screws countersunk as well,
and also have a little bit of consistency.
After checking that it was square, I had the top frame done.
And with the help of TV magic, the identical bottom frame was made as well.
Next, I cut the four lugs to length, and could begin installing those to the top frame.
Now it's important to notice here that I'm assembling this workbench upside down.
So I started by laying my top frame on the ground upside down before adding these lugs.
I used a squeeze clamp to hold the lugs in place before pre-drilling and driving in
four 2.5 inch screws in each lug, making sure to check for square along the way.
With the first lug installed, it was simply rinse and repeat for the remaining three lugs.
Next, I cut four inner lug pieces to length, and installed those on the inside of the outside
lug pieces I just installed. I hope that makes sense.
Since I'm building this upside down, I rest the inner lug pieces on the underside of the top
platform. Then, when the table is flipped over, these pieces will provide direct support under
the top platform, instead of relying only on the screws from the side.
And with the inner lugs installed, I could set the bottom platform in place,
and secure it with even more screws. In order to make this workbench mobile, I needed to add
some casters. But first, I needed to add some blocking in order to have enough material to
mount the casters to. For this, I just used some scrap 2x4 pieces, and then another full length
stretcher piece to give it some strength. With the blocking in place, I could mount the casters.
Now, it's important to make sure that they can fully rotate before mounting them in place.
Ask me how I know. I took a speed square to square them up, and then pre-drilled the mounting holes.
Then, I attached them with some screws. But, I think I might come back later and replace
these screws with some bolts, just to give them a little bit more strength.
With the casters in place, I could flip the bench over and give it a test spin.
Alright, so now that I've put this 8x4 sheet of plywood on top of here, my first reaction was,
man, it'd be nice to have eight feet of work surface, but I don't need that for the CNC.
So, my next thought was, well, I built this basically the same way that I built my workbench.
I just got it built out underneath there with some drawers. Maybe I can swap that out. But,
then I realized, or I remembered, that I raised this bottom shelf up a half an inch. So, I was
going to swap those cabinets and put them over in this one, but that's not going to work because
now these cabinets are a half inch too tall. So, my third plan of attack is, I'm going to
unscrew this top, which is six feet long, from that one, put this old top on my new base,
and then put the new top on my old base. And that will accomplish a few things. That will
accomplish the, I only need six feet of work room for the CNC over here on the new base,
and then I can overhang this side, which will be the front edge of the off-feed table
over here. So, we'll get that front edge that much closer to my fence and to the back of the
table saw. And so, I'll have a lot less, a lot fewer smaller pieces falling down in this gap,
which has kind of been an issue. And I just haven't gotten around to extending this out.
So, that's going to solve that problem. Then on this side, where I have approximately 18 inches
hanging over there, I can just extend this frame out on the base a little bit further,
and then I'll have a nice area on the end of my workbench. I can pull up a stool underneath there,
and if I ever want to sit down and tinker on something, I can do so on that side. So,
I think that's the new plan of attack. I'm not too worried. I know you can see the coloration
between those two. I don't really care because that's going to be covered up with a piece of
MDF for the most part anyways, because that MDF will be the sacrificial board.
So, let's get after that. So, like I said, I'm basically taking the old top and putting it on
the new base, which is my CNC workbench. And then I'm putting a full 4x8 sheet of
plywood on the whole base, which is my main workbench. So, one thing that you guys might
be wondering is why did I make this workbench six feet long? And the answer to that is because
OneFinity actually puts out a few machines. I have the X50 Woodworker, which is a roughly 32
by 32-inch cut area, but they also put out what they call the Journeyman, which is a 48-inch
X-rail. So, down the road, if I ever feel like I'm being limited by this 32 by 32,
I can always upgrade this X-rail to the 48-inch X-rail, and I have plenty of real estate over
here on this side of the workbench, and I don't have to rebuild it. But since this is my first
CNC machine, I just really wanted to make sure that I enjoyed it first and that I could start
making the things that I wanted to, maybe turn a profit down the road before going all out and
buying the biggest machine that they offer. So, yeah, that pretty much wraps up this entire
project. It's a super simple build, like I said, and you can honestly knock this out in probably
about an hour or two. Now, I did build this for my CNC machine, but like I said before,
I actually built a similar carcass to this a couple years ago, and it's sitting right over
here, and I've kind of built out the bottom area, and it's my main workbench. So, you could easily
build this carcass and then build out this bottom area to whatever your needs are. With that being
said, you may notice that this entire bottom is empty right now, and the reason for that is I just
want to start using my CNC machine and see what this kind of develops into. I really don't know
if I want drawers or doors or shelves or whatever down here, so my hopes is that once I start using
this machine, that it will kind of influence what I want this bottom area to look like. But one thing
I do know that I want down here is some type of dust collection, and for right now, I think that's
just going to be a shop vac sitting down here, so that will occupy some of the space. If you guys
enjoyed this video, it would be awesome if you could hit that like button down below. That just
really helps me grow my channel, and it also tells YouTube that this was a decent video, and maybe it
should pass it to some other people to watch. And while you're down there, consider hitting that
subscribe button as well, only if I've earned it. That way, you're notified every time I release a
new video. I really appreciate you guys watching, and until next time.
