How To Frame A Stair Half Wall

The Stone Cube
31 followers
18 Video Views·Nov 3, 2022
How To Frame A Stair Half Wall
All right and I just want to say this real quick. Please be sure before you do any demolition work
that the work that you're planning to do will not negatively affect the structure of your building.
So I know that I have a beam running across here. It's right above that two by four that
top plate there. I know that with or without this wall in here that my structure is going
to be fine. The floor above it is going to be totally supported by that beam running across.
But please be sure when you're doing your own work if you don't know please seek help from a
professional. Please get a professional's opinion on the work that you're about to do before you
start ripping out any walls. All right now that I got that portion of the wall ripped out I'm going
to go back and frame this in. And eventually there's going to be some banisters sticking up
there and then the handrail is going to continue down. Right now this is a little bit rough and I'm
back and cut the jib flush with the top of this board that runs down the side of the stairs.
So let's get to it. To start I'm just going to use a razor blade. I've got a fresh blade in there
and I'm just going to score along this edge. Same thing on the bottom here. Right now I'm
just going to trim it flush. All right so along this edge is fine. Now I got to trim up by the
top 2x4. All right and since that was such a thin piece to cut off I guess it was just a little bit
easier to cut it from the finished side. And just do your best to follow the 2x4. All right so now
we're in this top corner and the first thing we got to do is get this angle right. So I've got a
combination square right here. I'm just going to take that top piece off. All right so I'm just
going to take this here and I know that this angle is 45 degrees on the tool and I don't know how well
you can see that but it doesn't look like it's quite 45 degrees. It looks a little bit steeper
so I'm going to try maybe 46-47 degree angle on my miter saw and see where that gets me. There's
another tool that you can pick up I just don't happen to have one. I think it's called an angle
gauge. I'll put an image on the screen right here but that will allow you to dial in this exact
angle and then mark that and cut it on the saw. I'm just kind of using the tools I have right now.
All right so after a little bit of trial and error I realized I was going the wrong way.
Actually this turned out to be about a 41 degree angle. So if I line it up there this is pretty
much flush right there and then it's flush along the top of the stairs right here. All right so I
like to let this bottom plate run about two to three inches past the sides of the stair
and then also then I didn't have to deal with trying to remove all these nails. So I just cut
it back a little bit and then I can start laying out my first stud right here. All right so first
thing to do is put an angle on the end of a two by four. Now remember we're coming out past here
so I'm going to measure probably to right about there just to be on the safe side. So from that
corner down to there I'm going to call this 62 inches and we'll be trimming this back later.
So 62 inches roughly turn this all back to 90.
All right and just so I can line it up a little bit more accurately every time
I'm just going to take my scrap. You could take this one if you if you want to but just take your
scrap it's the same angle and line it up so it's flush right there with that stair board and then
just strike a line across the top. This will help you just line it up at the same spot every single
time. Also help or I also find that if you're working by yourself just get a little clamp and
once you get this angle in place once you get this this piece in place just put a clamp right
there and then when you're working on the opposite end you can just set it on top of the clamp it
should line up right there and it's a another it's an extra hand for you. All right now we're going
to line this plate up to be flush with this stair right here. So go off our mark right up top that
we just made and then just kind of feel you can look at it to look at it from the side make sure
that it's flush at the top. It also helps obviously if this board this top plate is as straight as it
can be. So once you get that in place again unless you got a helper to hold it in place for you
I like to take a few clamps and clamp that in place.
All right and then you can kind of double check it make sure that it's flush.
All right that looks pretty good. All right so now we're down here at the bottom again
I'm just using that scrap from before and placing it right on the end of this bottom plate
and once I get that in place you can double check that it's a square and it's nice and plumb.
Let's take a either the speed square whatever square you got and make sure it's nice and plumb
right there. That looks good and I'm just going to make a mark along this back side
at the angle of this top plate. All right so right there so again just that's right in place here
it's nice and plumb and then just trace along the bottom here that angle that's going to be
that 41 degree angle right there but that's going to give you the exact dimension that you need to
cut it at so let's go cut it. All right so we got that cut to size and if it's in here
nice and snug like that.
All right so that's perfect. All right so now we got that bottom block in place just
temporarily right now and so we can take a straight edge and right along that edge of it
nice and straight and just draw a line and now that's where we got to cut
that same angle on this top plate so let's do that. All right and if it all goes to plan this
should line up perfectly look at that right there and I just like to pre-drill and screw this block
into place along with this part right here. I'm going to drive a couple screws down there just
because this block is so small and it has a tendency to crack especially when you're right
near the end of it. All right so now we got this top plate in place and we can begin laying out
our studs that we need. All right so my studs are actually laid out already from before when I had
studs going all the way up to the ceiling but if yours aren't just hook on to a stud back
and then mark out your 16s. So right here I got a 16 keep it hooked on there I got 32 right there
and then 48 is actually past the end of it so I've got two studs one right here one right here
and I will put the x on the left side because that's the way the way that I was pulling the
tape out and also I hooked on this side on the right side of this previous stud so if my 16s
here then that's on the right side of this stud and my studs are going to sit on the left side
of my 16 marks hope that makes sense. So we got our 16s marked out on the bottom
now we got to transfer that up to the top so what I like to do is take a square
and bring your marks out to the edge okay and then you can do it along the face here as well
same thing for this one
right about there now take I have a four foot level but take whatever size level you need
and put it right on that mark that you just transferred over there and then find level
on your level right so that's a level right there I'm going to make another mark right here
okay now we can do that on this side as well put the level on your mark find level
just right there and draw another line on your top plate we know that on the bottom plate the
stud sits on the left side of that mark so we'll mark an x right there on that side same thing
for the other one all right now to get the length of that stud we'll measure from the top of this
plate to the bottom of right there on that mark and that's going to be our long edge of the stud
so it looks like 14 and three quarters I'll measure this one too so 14 and three quarters
was the other one this one is 27 and three quarters just put them in place make sure
they line up right on their marks that one seems pretty good that one too all right now we can just
toenail them in on the bottom and then screw them in on the top all right and this last one's a
little bit unnecessary probably but just to give a little bit of support under this top
part of that top plate I just cut one of these to size
like that like I said it's probably unnecessary but now this is resting on something instead of
just being pinned in from the side so just drive that guy home all right and that's really all
there is to framing the opening on a stair like this so next what's going to happen is the dry
waller is going to come in pretend this is drywall and just install drywall right here along this
face and then he's going to cut it off flush with the top of this top plate and so once the drywall
is done then I can come back with a piece of one by material and just put it across this top like
this and that's going to act like a cap right there and it's going to be a finished piece of material
probably something to match the sides of the stairs right there and once I have this capped off
then I can run my banisters and my railing all the way down to the end here all right so if you
guys enjoyed this video and you feel like you learned something and you feel that I've earned
it go ahead and hit that subscribe button down below and while you're down there go ahead and
hit that like button as well that just lets me know that this was a decent video and maybe I
should make some more videos just like this but until next time thanks for watching!
