Building the Bouchie Dory - Part 36 - Final details

Nomad Boatbuilding
98 followers
1 Video View·Feb 6, 2022
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
We're getting so close I can taste it. So just a few finishing details today.
Let's go tidy up the top of that transom and we're going to do a little bit of grommeting
and I'm not sure what else might be on our plate but we will get to it and then it's time to
splash. But we can't splash until we finish her up so let's get right down to work. Sit back and
Just boring holes for the rope strop for back here. I've drilled a little bit. I've done a
pilot hole all the way through and come up from the back side of this drill about half an inch.
I want to end the hole in the center somewhere.
There we go. We'll put some copper liners in there before we're done.
Once you bored the holes for your liners we're just going to chamfer this outer edge a little
bit. So I've just got this chamfering bit on this drill here. Don't need a lot, just a little.
A traditional detail on a lot of east coast dories is this rope strop or becket. Now these were used
to be able to sling these boats over the side of a schooner. You'd attach a piece of tackle onto
this and hoist it over the side and you'd retrieve it the same way. So they're quite useful and just
having something you could hang on to for hauling these boats around or even tying an anchor line
off to. This is a nice little detail. Now what I want to talk about is the holes that are going
through here. Now you can just bore a hole certainly and that's just fine. What I don't
like is the fact that these holes are really a great spot for rot to start. It's easy for junk to
collect in there and moisture tends to sit in there a lot especially if you've got a piece
of rope going through there. What I could do is paint these out with epoxy and that would be okay
but if you have a nice a copper sleeve in there now that's a really nice detail. It makes the
rope easily slide in and out. You don't ever have to worry about painting in there in the future.
Gives it a really nice finish. Now this isn't something you can purchase. You've got to make
these and it's not very difficult to do. So I'm going to show you how to do that. I'm using a
standard piece of 3 1⁄4 inch pipe here. So it's 3 1⁄4 inches ID and it's about 7 1⁄8 OD
outside diameter. You're going to want a piece of hardwood or plywood with a hole board in it
that matches the outside diameter of your pipe. Now I've actually put a slit down into here and
that's so that I can get a good squeeze onto it. You want this to be a tight fit. We're going to
be using this to help form the grommet or the flange of this pipe. Now you want to take your
chamfering tool and you want to chamfer out the inside of that a little bit. You don't absolutely
have to do that but it's a good idea. Our first step to doing this is getting a nice clean cut
on one end. Now if you have a plumbing pipe cutter that works best. If you don't it's a hacksaw job.
But you want to make sure you file this down so it's nice and flat. This is where your mandrel
can come in handy. If you've got a drill press that's the best thing. You drill this hole on so
that you get it nice and square. You can use this wood mandrel to help you get the top of this pipe
nice and flat. Once you flatten the top of this it's a good idea to take off any burrs on the inside.
It's not absolutely necessary but it helps. We'll take a fine file and we'll just try and
break that sharp corner on the outside too. Okay so now we're just going to slide this down onto
the mandrel a little ways. We're just going to use that to hold it up. Now what we're going to do is
we're going to anneal this. So you want to take a propane torch. I want to bring this up to a nice
cherry red and just hold it there for a moment. All right there we go. Now we're just going to
let that cool on its own. You don't need to quench it. It's easier just to walk away for a few minutes
and let it cool. If you want to quench it that's fine but just don't do it right away. Give it a
little bit of time. Once your tubing is cooled it will stay annealed for about the next hour or two.
Now we're going to set a height above our mandrel of about 3 16ths of an inch for this size tubing.
Now we need to form the lip or the rollover. I'm going to start by using one of my riveting tools
to flare the end out. You can also do this with a ball-peen hammer or anything you have around
the shop that flares out a little bit. So once you've got that flare coming over you can switch
to a smaller ball-peen. Gently work your way around. Once you've got that starting to get
close to flattened out you can switch to the to the flat face of your hammer. These are just gentle
blows. You want to ease this over slowly and easily otherwise you could start a crack on one
side. That looks really good. So what I tend to do is just give this another whack with my mandrel
here after I've sort of flared it over. I think that looks pretty good. What I'll do next is I'll
slacken off my on the vise here a little bit and just drive it up a hair. Just a tiny little whisker
maybe just a sixteenth or less and now I'm just going to try and mushroom that down a little bit
further. In fact what you can do is you can take something else to use as what we call
the chasing tool. So I'll use this cross-peen hammer for instance.
That's just going to help roll that corner over a little bit. Okay that looks pretty good. Now when
this goes into the boat of course it may have to conform a little bit to whatever the surface of
your transom is or whatever surface you're trying to put this into. You can at this point if you
want sand it out a little bit. So now we just need to cut our tubing to length. I use a scrap of
wire with a bend in one end fed down through the hole in the transom to find out what length the
tubing needs to be. Okay now we're going to take our piece of wire we're going to mark this for
length. So I'll just use the slot in my mandrel to mark the height. Okay now I want to add an eighth
of an inch onto that. Not quite 3 16ths because I find when you do this last bit of installation
if you have too much of a flare it's hard to deal with on the boat. So we want a smaller flare on the
on this other side. So if I dial that in till I get down to my finished height. If I had my
pipe cutter I'd be using that but I don't so I've got a hacksaw. So my mandrel is going to help me
here to keep this cut nice and straight. I'm just going to soften the outside corner of this now.
Okay now we're ready to re-anneal this. So what I want to do is anneal this end of the pipe. This
ends fine although if it got annealed just a little bit more in order to conform to the face
of the transom that wouldn't be a terrible thing. The coffer is pretty soft. You can probably get
it to bend regardless especially because this has been thinned down a little bit by the pounding.
We're going to hit this side until it turns sort of a dull red. Okay you want to take your liner
and just test it for a fit. You want to be able to slide in there easily. It shouldn't be too tight
because you need to leave a little room for wood expansion.
There we go. That's a nice fit right there. Just got a little tiny bit of wiggle which is fine.
That'll tighten up once you've peened over both ends. Okay now for the installation. I've given
this a liberal coat of dolphinite bedding compound. I'm just going to slide that in there
and I'm going to clean off that bedding compound before I go any further or else it's going to get
rather mucky. I've got this three jawed clamp that I'm going to use. I would just have somebody else
hold an iron on the back side of this but I just don't happen to have anybody at hand that
is able to assist me at the moment. So this will have to do. I generally like to
have the side that I've done on the mandrel
on the show side and then we'll peen the other side in place.
All right we've got the same tools as before. I'll start with this tool for flaring.
I'm going to put another tool here. I'm just going to help to help flatten that out a bit more.
Okay now I've taken the clamp off and I'm just going to use one of my irons on the back side
to back this up as I do this peening. All right up here at the bow things are just a little bit
trickier. I don't have the room inside to swing my irons the same way. Let's see if we can figure
out what to do here. Let's see if I can just start peening this from the inside.
This is tricky enough to do right-handed now I've got to try and do it left-handed.
It's right about now that I wish I'd decided to flare these on the outside of the boat instead
of the inside but nonetheless we got them done. They look good and this one little detail I
really love doing. I think it adds a really great sense of craftsmanship to the finished product.
So we've got the sculling notch here. This gap should always be wide enough to drop your oar
of course. That's looking pretty good. I got a little bit of work to do to sort of sand out this
joint in here. It's a bit messy and when I cut this what I want to do is I want to cut this
so that it largely matches the angle of the shear. So that's kind of the tricky part. I kind of take
this in stages. I'll probably take a saber saw perhaps to just worry about taking off the tops
here like so at the right angle and then I'll worry about how the angle on the sides is dealt
with. Kind of whittle it down a little at a time. Okay let's hope I don't make a total mess out of
this. This is about as tricky as it gets I think. Okay that's not a terrible start. All right I'm
going to try and very carefully use a coping saw to bring this down. I'm not sure if this is going
to work very well. I try this different ways every time. There we go. So I gave myself a pretty
healthy margin of error there. I could even use this piece. I could flip it over if I wanted to
and use it to try and mark the other side. But you can see I'm actually pretty darn close to my line
so I'm happy about that. So there's still more work to be done there. I'll do the other side
the same and then we'll move on to the inside of the notch here. So the trick is getting started
trying to keep that angle. So
okay that's pretty good. A little rough but that'll all get smoothed out. Now the idea of
bringing this around and then matching it square to the inside I think you'll do this side first.
That other blade isn't biting very well so I'm just going to switch saws here.
Okay the toughest part about that is not beating up the rest of the boat. I got a
couple little scars on here that I'm going to have to fix. I'll move on to the other side.
I'm not a slave to my lines. They're just a guideline. I'm comparing one side of the transom
to the other. It's more the shadow lines that are guiding me. I really wish I could just leave these
lines crisp. I can't though because they'll just get damaged in use. It's so nice to make them in
the first place though. I'm just going to soften the top one here. I'll leave the outside one a
All right as I'm working on this I like the way this is shaped but I'm having a little
trouble trying to get this one to look exactly like that. So here's a little trick you can try.
I'm just taking a piece of tracing paper and I'm just going to sort of... it's got a straight
edge on the bottom so I'll just kind of find a happy medium there. I'm just going to carefully
rub the corner of this here like so. All right and then we're going to flip this over,
line it up as close as I can the same way and we're just going to rub this down. So you just
go over that line trying to make sure you don't move the paper while you do it.
Okay and there we go. It's quite a bit of difference there so I'm just going to take
some time to work all of that down. I'm surprised at how different that is because it looked very
even when I was starting but that's the way it goes. I'm just going to soften this one out
get to that inside like that.
Soften out that one.
Just carefully soften a few details and there we go. The biggest trick with oiling is just not
missing spots. The cedar is really soaking the oil up especially this dark this darker
cedar plank right here. For some reason that dark chocolatey cedar is always very very absorbent.
Okay that's it. That's it. We're done. We are ready to launch and so we'll be back to do that
in the next video. Thanks for watching folks. I want to thank everybody on Patreon to help
support the videos. You can help us out on Patreon. I really appreciate that.
Links in the corner down in the description. Ciao for now.
