I restored my Grandmother’s 1950s pantry cupboard

Antique Art Deco
12 followers
#furnituremakeover #cottagecore #restoration
Chapters 📖
00:01 Getting the cupboard out of the barn
00:44 The plan
01:14 Removing the hardware
02:20 Scraping the paint
04:03 What's next?
05:25 Cupboard doors
06:25 Soaking the metal in vinegar
07:15 Taking the cupboard apart
08:44 Stripping the paint & varnish
09:54 Sanding
11:08 Putting it back together
13:13 Mending the drawer
13:49 Repairing the enamel work surface
14:31 Mysterious shelf
16:08 Cleaning the brass hardware
17:54 Repairing the hinges
19:47 Brass 'plated' hardware
20:22 Reassembling the cupboard
21:55 It's finished
24:08 So happy!
Follow me 😊
Instagram: / kenkyo.studio
Tiktok: / nelferch
Comments are disabled for this video.
In one of the old barns on the farm there is a pantry cupboard that my grandmother used.
It has a fold-down door with a work surface inside
but it's covered in old paint and broken in places.
My plan for this old cupboard is to strip it down completely if I can,
just take off all the paint and maybe if it comes apart easily take it into pieces
so that I can mend everything and put it back together really nicely.
It's got these interesting little old fittings and I would really like to
keep them. Same for these hinges and little door clasps.
To loosen the paint and remove the screws I use some paint stripper.
I took off all the metal parts and also the enamel work surface.
I used a wire brush to scrub away most of the paint from the metal pieces.
Looking at this I think under the paint there's some varnish and it seems like the paint isn't
that well stuck so I'm gonna just try scraping off as much as I can to begin with.
Well the good news is this works, it's pretty effective. The bad news is it's really tiring.
Yesterday I scraped off the paint from the front and the outside and now I need to tackle
what's going on on the inside. I'm going to try and remove as much of this varnish as I can to
get it back to the bare wood and see if that might look nice. I found this piece inside that says
1950 so I imagine that was when it was made which is actually a bit older than I was thinking.
So here I've got all the metal pieces. The paint stripper took off most of the old paint.
They all need some further cleaning to get off the rust. There's quite a lot of rust on there.
The cupboard doors need the paint removing from them. Also this drawer probably does need
some mending. It's not looking the best. The board in the bottom is like
delaminating so I might need to replace that.
Hy...hy...hygiena? Hygiena maybe is the brand of this.
I spent ages scraping the paint away using a blunt ball chisel. The thing about this is that
sometimes the paint comes off really easily but that's because of the varnish.
Like this door I can tell has much more varnish left on it than these and while that makes it
easy to strip off the paint it just means I'm going to have to do a lot more to get
rid of the varnish afterwards. So I will probably just have to sand these down.
Okay I've had this metal hardware soaking in some vinegar for a couple of days and I'm now
going to try and give it a clean. The vinegar soak worked really well on the brass pieces.
The before and after is really clear on these door catches.
This cupboard is looking quite rickety and actually some bits of it are already coming apart.
So I'm actually thinking I'm just going to take it to pieces and then sand it down,
mend it up and put it back together. On the back here it's got this like kind of board,
thin wooden board that seems to be warped and I'm wondering if I should just replace this.
Okay I've got this cupboard mostly into pieces now which means I can much more easily take the
off all these little bits and then just mend it up and put it back together.
I also removed the paint from the inside areas of the cupboard.
So I've managed to remove all the paint from the pieces of this cupboard now.
There is still quite a bit of this very old yellowed varnish that I would like to remove
and I think I might try some paint stripper before I try sanding it
just to get off as much of this sticky old varnish as possible.
All right I have stripped off as much of the varnish from this as I can. It's looking okay
but there's a few areas that I think I need to still sand to try and just take off the last bit.
Some parts of the wood frame had come loose so I found a modern version of this corrugated
fastening used in other parts of the cupboard. Okay I've finished sanding this cupboard. I've
sanded it so much and I cannot bear to do any more so it's time now to put it back together.
I also ordered a new piece of plywood for the back so I need to cut that to the right size.
I also replaced the plywood on top of the cupboard and cleaned up the brass
screw cups using vinegar. I'm going to reuse these old screws that I cleaned up
but I'm going to put new screws into these bigger screw cups because these are actually
for some reason now too
small and they just go through maybe because these got bent when I removed them.
I took the base pieces out of this drawer because they were looking really gross and
the ply was delaminating so I've cut some new pieces and I'm going to put them in
now hopefully if I can remember how it goes together. Okay the other thing that's pretty
cool about this cabinet is that this thing which is like the enamel work surface
is actually in pretty good condition like normally old enamel is just chipped and rusted
so there are some scratches on this from use but they're not so deep that they
break the enamel it's just along the edge here where it's a tiny bit rusted.
I used some wire wool to clean off this rust and painted the edges with enamel paint.
Okay I've honestly been debating whether to put this weird half shelf back or not it was
originally like this but it's such an odd shelf I don't know why it's like broken into these three
pieces and it's just not very sturdy so I think I will put it back for now because it's the thing
that has 1950 written on it which is kind of cool but I'm honestly not sure what this is about.
I feel like it might be something to do with this strange thing that went up here it has
these runner things so possibly there was something in there that slid out but why
you would need something below made like that shelf I am not sure. It's just so strange because
I can't believe you could put anything on it that it would hold it just is so weak and flimsy.
Okay so since I pinned this in from the back with pal pins it's actually a lot stronger
but I still don't know what it's for and why it has this section which is made of
different pieces of wood. So I finished cleaning all the little metal pieces like the handles,
clasps, some of them look really nice like these things are solid brass I think and they look
great. These bits which are the things they hook onto are also brass but they are looking kind of
pink and I read online that this is copper and if you put it in some chemicals you can actually
remove that excess copper and make it more of a classic brass colour. So I'm gonna try this I've
never done it before but I've got three percent hydrogen peroxide and sodium bisulfate and after
I put them in that I have to neutralise it in bicarbonate of soda so I'm gonna have a go
and see if it does anything. I guess this isn't essential it doesn't matter if this doesn't work
but I just thought I'd have a go and see if I could learn something new or maybe it's working.
Okay well it worked which is really exciting this one is looking so much
golder and brassier than this one so the enamel paint on the edges of this has dried
and I think it looks really good. These are how my hinges are looking currently they are
pretty badly corroded on the surface so I've been wondering what I can do with these hinges
to make them look a bit better. I came across something which I got really excited about.
I found that some people online have been putting brass onto other metals using a heat torch and
a brush made of brass wire. Basically you heat the metal and then you brush it with the drill
with this and some of this brass actually melts onto the surface of your piece of metal
and the results people got looked really good. I haven't got a propane torch I borrowed this
catering torch from the pub that I work at. So first I need to really clean these down
I'm going to use the regular wire brush on the angle grinder.
Okay I am extremely excited about this but I also have no idea if it's going to work.
the cupboard was really heavy once it was all put back together.
Okay I'm so happy with this cupboard I love it I think it's beautiful and everything works
these little things close and these things twiddle. I am so happy it's taken so long
like much longer than I thought but I'm really pleased with how it looks.
Yeah I can't wait to use it for things at the moment it's mainly just
for storing stuff. So in the top up here I put my weck jar canned fruit like my apples and plums
and inside this section I put my dried teas
all my mint tea also my apple slices that I dehydrated and some bowls and plates and in
the bottom here I've got more canned apple the damson jam I made and the canned ginger pears
as well as some of my dried seaweed and dried mushrooms and other forage food.
I left the wood completely bare at some point I might put something on it to protect it but right
now I didn't want to spoil it because I love the look of the bright light sanded oak. I am so happy
with this project.
