Timer Switch की ये Trick नहीं पता, तो आपकी Wiring Knowledge अधूरी है! @ElectricalTechnician

99% OF ELECTRICIANS FAIL IF YOU WANT TO TAKE A DIGITAL TIMER IN WHICH WE DO TIME PROGRAMMING IN THIS DIGITAL TIMER I TELL YOU DO ONE THING THAT THE LIGHT THAT LIGHT ONLY 10 SECONDS TO START YOU WILL SAY SIR, IT WILL BE VERY EASY I WILL DO TIME PROGRAMMING IN THIS BUT FRIENDS IT IS NOT IF YOU GO TO DO PROGRAMMING IN THIS TIMER THEN YOU WILL SEE ONLY ONE MINUTE MINIMUM TIME YOU CAN SET IF YOU WANT TO SET TIME IN SECONDS THEN IT WON'T HAPPEN THEN YOU WILL SAY SIR, HOW TO DO THIS IS THE QUESTION LET'S UNDERSTAND IN FULL DETAIL LOOK TO DO PROGRAMMING IN TIMER FIRST YOU WILL SEE A LOCK BUTTON TO UNLOCK THIS BUTTON PRESS LOCK UNLOCK SET THIS BUTTON SET TIME THIS BUTTON SET unlock LOCK UNLOCK YOU OR HELP DEATH WE We can set the minimum here It must be at least a little bit of cheese; it cannot be less than that. So I've set it here for 20 minutes. After setting it, I click on this button now Now the second programming has come up here, I don't need to do second programming, so I'll just skip it, I'll press the clock button, it will go back, and here the time has already passed, one minute, click the set button here We do it at 7 minutes and 19 seconds; we'll have to set it to 20, and at one point here we'll have to set it to 21, and we click the left up button, proceed, at 7 minutes and 20 seconds the light will turn on automatically, you see. You should know, at some point you'll see, this digital timer here, the minimum time I can program is 1 minute. Now friends, if you want to turn this light on only for 10 seconds, there's a trick you can do. So, please use this timer, because only through this timer can we decide here at what time we need to turn on the light, but after it turns on, we need to manage the power flow within 10 seconds. No, in that case, please use another timer here. I'm using an on-delay timer here, and through this timer, I'll create this latch. Let's understand how it will turn off. Look at what happens at the final time. But in this saddle, there is a valve here, so I'll just close it on this trunnion. After this, we'll also need to provide a neatle, so for supplying the neatle, the neatle ball located here on the trunnion, please open it. When this time comes, it will activate the veterinary from Yuto Jadu Bar. I want to take a picture of this slide, so please focus the camera on the slide. For the sake of the sacred flame, first let me cleanse this candle sword. In this timer, the 15-number terminal is common. I need to provide phase supply here. And from where will the phase supply go? Just understand simply that only after this timer turns on So I need to power this light. 明年就会有电力供应。 It must take the output phase supply from this digital timer. Or here, the Ewen terminal, which is connected via the cable here I can also lure him here. So during Philal's time, I connect a wire to the phase terminal at this location on the digital timer's output terminal. And I will take the other end of this wire. I'll connect this wire to the common terminal marked number 15 here. Now, the common terminal, which is the power supply, connects to both the NC (normally closed) and anode of this timer. Which time limit is for ENCI? It's 16 number, and the one that is ANO, that is 18 number time limit. Now, friends, here's a small question for you Should I use this timer here or NC? Tell me in the comments... let's see how many people give the correct answer If you don't know the answer, you can comment... Sir, I don't know. Please definitely contact me, so that I can get to know Depending on how much you people have understood, the upcoming classes and videos will be according to that. I'll create it so that I can provide you with even better, more accurate labeling for electrical training. Alright, here's the answer: the NC of our timer is the one we'll have to use. Now tell me, sir, why will you use NC or why won't you use it? This light is mine; I need to keep this light on continuously. I'll use NC here to proceed. Now, sir, where should I provide the continuous power here? You have to make the light glow at the exact moment the digital timer finishes. And if we use NC at that time to make the light glow, the light will glow permanently. You see, it won't happen like that, why? This power supply comes from the face supply of this digital timer, meaning it is coming from the output side. So when the output power is generated, the power will come in on the power. And this power will operate the bulb. Now the bulb will remain continuously on. But as soon as the timer's time is complete Then it will lose power. But I have to make this light before that. I will do programming for one minute. But I need to make the light turn on within 10 seconds. So, to program for 10 seconds After setting all that, just one wire remained. The wire that provides the face for my bulb So, bring this wire here. This jagapé with NC is teringal number 16. I will easily connect this wire to the jack. Moreover, if my 12 years of work experience knowledge is concerned So, I have two books here for you. A book titled Electrician A to Z Wiring Book Where you get complete knowledge of industrial wiring In this book, you will see here the complete diagram Everything has been taught at a high level from Maḍhiyam. By reading this book, you can gain knowledge at a good level. Moreover, if you are working on house wiring You will need to buy the "Zero to Hero House Wiring" book for house wiring. I have explained everything related to house wiring in this book. This book will be available in both PDF and printed copy formats. I've provided the link to both of them in the video description; you can bid from there. Otherwise, directly write "Book by" on this WhatsApp number. I will provide you with the link; please place the order from there. You will make the payment, and after making the payment, you will send me the screen shot. I will provide you with the PDFs of both books directly on WhatsApp. Here, after it leaves, you can see the setup button. Now, what time is it? It's 7:30, 31-30 minutes. But I want to turn it on; I'll click the setup button at 7:20. If you want to change the program, you can do so; I'll just take a new program. Here, we will set up a new program, so I click this button. I have to be here in 7 hours and 21 minutes to do 31. Set the time to arrive at 31, and the time to leave is 32 minutes, not 30 minutes, I'll be here for 32 minutes. It's done. Then I'll click the Set button here. This is the third time I've programmed it; I'm done with this. I'm leaving the bag, click now, check here, 30 minutes and 38 seconds are passing, as soon as it reaches 31 seconds here Here, the light will turn on. Let's set the timer a bit. You've seen the light has turned on here, and the timer has also received power. Now, once the timer completes its set time, the light will turn off. When this timer's time completes, the digital timer's time complete signal will be set. As soon as the light turns on here, it will activate. Until then, as previously mentioned, it will remain inactive. If you work at a company, whenever there's a break or lunchtime, doesn't a siren go off? So, the siren, as you can see, often stays on for about a minute. Why does it keep running? Because the digital timer used there is set to keep it running. And in this, we can set the minimum time to one minute. If you want to reduce that time, you want it to ring only up to thirty seconds, and not beyond that. So you can do this wiring there. Thank you so much for watching this video today. I hope you enjoyed it.