Basics of Inlays and Onlays - Conservative Indirect Restoration with CEREC Omnicam and MCXL

Dave King
65 followers
271 Video Views·Jun 17, 2026
AI Generated·May contain errors
Hello there, this is Dr. Dave King again. I wanted to go ahead and recreate the lecture
that I just gave to the dental students at the American Student Dental Association
recently here at Kansas City at UMKC where I went to dental school.
So this is the lecture that I gave, The Basics of Inlay and Onlay, an Introduction to Conservative
Indirect Restorations with CEREC, Omnicam and MCXL. So I've been using CEREC since 2006.
Since I came out of dental school, I bought two units late in 2006 and have enjoyed it ever since.
Really a great, great solution to provide restorations, indirect restorations, conservative
inlays and onlays like you can see here in a way that allows our patients to,
provides a great service to them. So this is me. I graduated, well rather I went to Central Missouri
State in 96 where I studied jazz and this is something that a lot of patients don't know about
me. A lot of people don't know about me for that reason. I was a jazz trumpet player first.
That was me first and foremost. Did that for a year then I went to Taiwan as a missionary.
So this is sui which is so in Mandarin Chinese. So I speak some Mandarin. I used to speak
very fluently and now I don't speak so fluently anymore because it's been so long.
But I still can understand a little bit of Mandarin from my time as a missionary in Taiwan.
When I returned from Taiwan, I was a business major again at Central Missouri State University.
My plan was since I could speak some Chinese, I'd go ahead and jump on the business train and
eventually work some international position. After that, I married the daughter of an orthodontist
in 2000 and changed my major to biology and chemistry preparatory to going into dental
school where I started in 2006. After graduating in 2006, I started a scratch start practice in
which is one of the suburbs of Kansas City. I bought another practice about a year later in
Independence, Missouri. I sold both of them, joined a group working at the same offices
in Independence and Liberty. And then I joined a Pacific dental services supported office in
Albuquerque in 2014. I worked in Albuquerque for about three and a half years and have since
relocated back to Missouri. I am on the St. Louis side of the state now near O'Falun, Missouri.
So that's me. These are some of the cases that I've completed,
excuse me, done with CEREC. Every single one of these has a CEREC involvement.
So if you look through these cases, very, very interesting. Up here we've got a same-day bridge,
same thing here, same-day bridge. You can see a five-unit bridge there. Here we have a four-unit
makeover right there. Same-day bridge. This one happened with an extraction, so we designed a
little ovate bullet-shaped pontic to go up into the extraction site. Same thing here, this dark,
dark, dark tooth number seven you can see there was extracted. And a four-unit bridge delivered
the same day. So all this stuff so far has been same day. This is as well a six-unit makeover,
a little bit of darkening there, which we did replace that crown later on. Down here we've got
halfway through, excuse me, this is 10 crowns, this is BL1, the whitest shade that I could,
I was comfortable going. There's a little bit lighter shade, but that's BL1 and Emax.
Done in one sitting, that was about four hours for 10 crowns. You can see his previous setup here,
wanted to open his bite, so we opened him a little bit. The plan was to do the lower teeth
at a later date once he recovered from the uppers. Here is one of my favorite x-rays,
five, three canals here, five canals total, endo with a nice crown there.
Here is another kind of a significant makeover case. You can see there's a five-unit bridge,
a three-unit bridge, and three individual crowns there. This essentially is a duplicate of that
one. Sorry, I didn't realize I had two of them in there. Here's just a nice endo case with a crown
on it, Emax crown. Some of the training that I've been able to do, I was able to help create some
coursework for the CEREC tie base restoration training. I was able to write an article,
I was asked to write an article about CEREC and same-day restoration modalities using
a surgical guide. You can see the guide in place there. It was interesting, you don't see the whole
picture here, but I dechorinated the tooth. You can still see the roots here. I dechorinated the
tooth. We drilled the osteotomy using the surgical guide. Then I took the roots out,
you can see little root crypts here, one, two, three, placed the implant. I had already drilled
the osteotomy, so the implant went right into the interferical area. There's the tie base
with the scanning body on top, and then there's the healing abutment with some bone graft material
and several stitches over the top to hold it closed. That was all done in one appointment.
We delivered the crown later, but that was all scanned and extracted and implant placed in one
appointment. This is a Serosmart case, so a single appointment, six crowns, six Serosmart crowns.
That's a GC product. I really like Serosmart. This was a patient who came in, you can see
significant caries there. She'd come in and wanted to do something about her smile.
She was a homemaker, had been frustrated for quite a while with her smile.
She had dramatically changed her oral hygiene, so I was very comfortable doing this.
But that was one appointment. Again, about two and a half hours, maybe as long as three.
This is the same case here. This is the same case there. This one, actually,
this guy belongs to that one. So you can see here's the restoration that went in.
You can see this slide is actually the same as that whole slide there. There's the implant
restoration right there, the Thai-based restoration. Very, very fun
procedure to do once you've done a few of them and you're not too stressed about getting them done.
Here is a standard, I believe that's an internal
hexagon implant platform there, a Nobel BioCare implant. There's the Thai-based
in place, and then there's the Emax screw-retained crown.
So I've had a great opportunity to do a lot of fun cases. I've got a lot of experience I really
enjoy. I'm not saying that I know everything, but I have had a lot of experience. So if any of you
have any questions, please let me know. I'm always happy to help create some more discussion,
topics, training materials as well. So here's the objectives of what we're going to go through
today. Hopefully I can get through this in about a half an hour or so. I'm going to kind of fly
through it. So if you feel like you need to take time to digest it, please pause the video. We're
going to define what inlays and onlays are. We're going to describe the rationale for an inlay or
an onlay, apply the principles of appropriate preparation design, appropriately diagnose an
inlay versus an onlay, identify various materials, understand inlay and onlay bonding protocols.
This is really, really critical, doing this correctly. And it's slightly different from
crowns, just ever so slightly. We'll talk about that a little bit. Normally, and I'll give you
a spoiler, normally when I'm putting an inlay or an onlay in, I actually apply the cement to the
tooth instead of the restoration. It's just too hard to hold the restoration covered with
cement. So this is what we're going to do today, really briefly, hopefully. So let's start here.
Let's talk about inlays and onlays. What is an inlay and onlay? Let's define this.
All right. So we know from the ADA that an inlay is an intracoronal dental restoration.
And here is the critical piece is that it's intracoronal, made outside the oral cavity
to conform to the prepared cavity, which, and here's another important piece, does not restore
any cusp tips. There are no cusp tips involved in an inlay. So cusp tips do not constitute an inlay.
If there's a cusp tip, then that's a spoiler alert going to be an onlay. But we're not doing onlays
just yet. So let's talk about the different inlays we can provide. Of course, we have our metallic
inlays and then our ceramic ones. There's also a composite inlay, which we generally call a
composite restoration. But you can also make a composite inlay depending on what you want to do.
Generally speaking, I use more than any of the other codes here. I use this one because almost
every inlay that I'm going to do has three or more surfaces. MOD or MOB or MOL or DOL or OBL.
Rarely is there ever a single surface inlay that I'll design. So here's the onlay. The definition
of onlay is essentially the same. It's a dental restoration made outside the oral cavity
that covers one or more cusp tips and adjoining occlusal surfaces, but not the entire
surface. All right. So and again, here's the one that I use most. It's most of the time this guy
right here, this 2643. But sometimes we'll get into the four or more surfaces. So all right,
let's talk about the rationale for an inlay or an onlay. Inlay or onlay indications. Insapient
lesions, recurrent decay around conservative restorations, correcting old restoration contours,
and any small to moderate size carious lesion. Why do we make that distinction here, small to
moderate size? Well, if you get a large one, that's probably going to indicate more than an
inlay or an onlay, probably a crown, right? So that's generally the rationale for small to
moderate. Usually the inlay or the onlay are more conservative, so I would limit it to small
and moderate. Anytime you get past a moderate size, you should be considering a core buildup
with a crown on it. So here are a few situations. Some of these pictures are mine, some are not.
The ones on the right side here, these are my scanned images or screen grabs rather from
the CEREC machine. So this one, in my particular experience, I would probably have done at least
an onlay there, potentially a crown. This one, obviously a crown. This one, yeah, we could have
gotten away with an inlay depending on how far it extended up. This is the unicorn, the single
surface inlay, which I don't get to do a lot of right here. Generally speaking, this unicorn
single surface inlay is difficult to do just because of where the sprue is placed from the
ceramic. And then of course, here's a three surface inlay. So indication for an onlay,
just an idea. Of course, we've got all this area involved here. There's also what looks like a
fracture here and maybe there, I'm not sure. So that would be something that you might consider
potentially a full crown on. But if we can save most, come up in here and remove that and cover
the occlusal portion, that'd be great. Something similar to this that you see here. So occasionally
we'll see this where you've got a fractured portion here and then we just prep off the
lingual portion or the buckle portion and we can save all this tooth structure with our inlay or
an onlay. So long-term success rates, these are some very interesting success rate numbers that
I'll just draw to your attention. Let's see. So survival rate of, let me highlight here,
survival rate of probability of 87.5% up to 27 years of clinical service of CEREC-1. That's
CEREC-1. So let's circle that, 87.5 at 27 years. Let me fix that, 27 years. And this is actually
the same study extended a little bit earlier. So this one has 88.7 after 17 years. That's
phenomenal. That's great for an inlay or an onlay. Some of these other studies, let's see if I can
find it. Estimated survival rates for glass ceramics at five years were 92 and 95%. That
dramatically beats out any composite in my experience. And here's another one, 95.5% for
five years. So we're talking high 90s, high 90%. All right. So definitely a good solution long-term.
And let me highlight that, long-term. Composites oftentimes are short-term solutions. Let's talk
about preparation design. Okay. Avoid sharp angles. That's probably the biggest takeaway here.
Avoid these sharp angles that you can see here. We want everything to be rounded and flowing. And
the reason for that is, especially when we're talking about CEREC, you've got a burr that's
going to be milling. Let's say this is the restoration. So we're going to assume that
this is solid instead of a negative right here. The burr, which is a circle, has to go in and cut
all these areas out from the outside, right? So it's milling from the outside. Can you imagine
having a circular burr that's going to try to get into that little edge or this area? Not going to
happen. Or that area effectively? Or that one? That's why everything needs to be rounded.
So we need to round everything appropriately and make sure there's enough extension for the burrs
to mill it correctly. Otherwise, when you try to seat it, you're going to get a nice fracture.
Here's kind of a problem there. Can you see that the round burr is not going to be able to get
into that spot? It's just impossible. Here's the proposal. You've got a sharp edge there. Round
burrs can't do sharp edges. You've got an incredibly sharp edge there. Round burrs can't do sharp edges.
So what'll happen is, because the computer is programmed to undermill on the margin where
there's a question, you'll end up with, you know, the ceramic will come around and you'll end up
with this rounded area. And then when you try to seat it, you'll get a fracture. You'll get a big
chipped portion there. Or it may even break all the way through if you push too hard.
So everything has to be rounded like we talked about here. You have to round everything nice
and rounded. None of these sharp, jaggedy, pokey things. We've got to have adequate reduction.
So here's the machine in process. Now it's in slow-mo. So you can see how those burrs are
milling from the outside in. So any area that's got a sharp edge, really sharp edge,
it's just not going to mill it. All right? So round your edges. Make sure you've got nice
emergence exits on your design. Okay. Here are our emergence profiles here.
So we want to make sure that we have nice, approaching 90-degree angle emergence profiles.
This one may be just a little bit shy of 90 in both of those. But the idea is we don't want to
have any unsupported enamel in these areas. And we want to make sure that cleansability is managed.
If you were to have this exit somewhere in here, can you imagine trying to clean and burnish and
smooth that area? So always bring, extend these out, break the contact to a point where you can
easily see it. There's no unsupported enamel. And you've got a nice, cleansable area, especially
for the patient's toothbrush. Generally speaking, when you're doing an inlay or an onlay, you don't
want to keep it ultra, super conservative and approximately like you would a composite,
just because it's so much easier to clean it, deliver it, cement it when you have a nice
90-degree exit angle that is visible and workable and cleansable to you and the patient.
Let's talk about axial walls.
The axial walls can be prepared vertically, converge or slightly divergent to the floor.
Now, ideally, we want this right here. This is our kind of our golden what we're shooting for,
four to six degrees of taper. And why is that? Well, you want the restoration to be,
you want it to mate perfectly with the internal line angles of the preparation. You want it to
actually physically touch the tooth. Now, if we have this, we'll have a bunch of cement that has
to fill in these areas. And will that work? Sure, it'll work, but it's not the best, the most ideal
situation. Now, if they're perfectly vertical, this could be a nightmare trying to insert,
trying to deliver. So always, always shoot for this golden four to six degrees. Don't
over taper it because if you over taper it, you know, if you've got this over tapered design
and you've got the restoration that goes in like this, you're going to have this
area that's really thin and you'll get a fracture through there. So you want to make sure that the
internal axial walls are as, you know, vertical or slightly tapered. Slightly tapered, of course,
is the goal. Slightly tapered for best long-term outcome. Alright, so here's a couple of ideas,
couple of examples to look at. We want to avoid these S-curves, these big S-curves.
Dr. McMillan, when I was in school, called that the crab claws. Nice straight exit angles.
Avoid these bevels here. You can see you got a bevel there. That's going to leave
a really thin piece of porcelain, which is likely to break off in the restoration. So avoid bevels.
You want nice strength of porcelain and strength of tooth. And that's what that 90 degrees
is good for. So gentle and rounded curves. We all know from ceramics that everything
needs to be rounded. We don't want anything sharp. Round and curve everything.
Proximal box shape. Again, we want to round everything internally. Make sure that it's
smooth and rounded. Avoid these sharp edges. Like for metals, for gold, and I've got a cast
gold inlay in my mouth, it's got nice sharp edges and that's perfectly fine for gold because it can
be blocked out in the process and filled with cement. But we want nice rounded edges. Rounded
is the key with anything ceramic. Slight taper 4 to 6. This one has 6 to 8. So very, very slight
taper. Avoid undercuts. Nice smooth floor and avoid sharp internal angles. That basically covers
everything with regard to proximal box shape. Check your depth. Two millimeters at the central
groove. Make sure it's not too shallow. Depending on where you measure it, it may determine how
deep it is. So check it at the central groove here instead of off to the side. You may have
this area may be too thin if you're checking the depth incorrectly. So check your depth at
the central groove. So be cautious of that. All right, here are a couple of inlays that have been
replaced. The key here is this guy right here. Adequate tooth reduction. It's easy to under
reduce and this will create challenges for us, problems for us going forward. So don't under
reduce. Make sure there's adequate tooth reduction. You're going to be replacing it with a high
strength ceramic bonded in place so you don't need to sweat removing a little bit more tooth
structure to gain appropriate strength. Okay, the only big difference between inlays and onlays
is the amount of reduction over the cusp tips. So and this essentially applies to almost all
all ceramic crown restorations. Two millimeters over functional. One and a half over non-functional.
We don't need to worry about metallic, you know, principles of retention form because these are
going to be bonded in place. So nice straight exit angles. That'll give you a lot of enamel.
This wide band of enamel to bond to. Really high bond strength. So bonded, again, we're not
cementing. We want to avoid these, avoid the mechanical retention features like grooves and
slots. We just don't need them. So look at all this enamel here. Look how wide that enamel band
is. Now wide that enamel band is. Plenty of enamel to bond to. A little sharp angle here. Be cautious
of that. This looks a little sharp in there. Potentially, depending on where the margin is,
that may be a little too beveled. You might have some thin spots there. But generally speaking,
all three of these are very, very acceptable. Passive fit. Avoid, again, these metallic
restoration features where you've got mechanical retention. We just don't need it when we're
bonding. Here's a beautiful preparation. This would be classed as an onlay because we're
covering this cusp tip. A couple of concerns here. Of course, you want to make sure you don't have
any undercuts here. And then you want to make sure you don't have any undercuts here. And then
the angle that's there. So just be very cautious when you're preparing to make sure that everything
is diverging slightly, four to six or four to eight degree divergence. But that's a nice prep.
Look at all the healthy, the tooth structure that they were able to save with this prep. Just
beautiful. Okay. All right. Let's talk about diagnosing inlays and onlays. When to recommend
them and how to recommend them to our patients. These are a couple of cases I've shown you before
here just a little bit ago. So here's the area, again, where you've got all this yuck here and
So there's the preparation of that particular tooth right there.
One thing to pay attention to is when you get these little thin areas where there's only enamel
that's unsupported, this might be, maybe, maybe a good idea to consider coming over and then
covering that whole back half of the tooth. Otherwise, in my experience, this, even though
it's bonded well, under occlusal forces may end up fracturing or chipping. But you can see,
beautiful. This is meshed very beautifully in there. It looks great. Bonded well,
little color difference. But I don't think anybody would notice that except for the dentist
and you and me. Here's one again that I showed you before. This technically would be an inlay.
That's a giant inlay. I don't know if this technically counts as a cusp tip. We might
be able to call that an inlay. But that's a beautiful restoration. A little bit of staining
here. That may become an aesthetic concern to the patient. I'm not sure if there's a little
piece of amalgam there or if that's just staining. Probably, honestly, I'd go for a crown on that
tooth. Probably. Although this may be a great solution, my worry is with that little line
that could potentially be a fracture. Remaining fracture. Might just be a marginal ridge groove.
But at the same time, I'd crown it. I probably would have crowned it. But this is a great
middle-of-the-road option, an inlay. Case study number three. This technically,
on the right side, I think that would be an onlay because these cusp tips are covered. You can see
the design. Looking back at this, these walls are too thin. Probably should have covered them.
In my experience, that's going to chip at some point. Here's this guy here. And remember that
one we said we crowned. So there's a crown there. This looks like a Cerismar or a Vita Enamic or a
Lava Ultimate inlay. I don't have post-op inter-oral photos. But radiographically,
it looks good. Looks like it was done well there. Here's a case study. I've got a bunch of pictures
of this one. This gentleman presented to the office. And this really goes, speaks to knowing
your own radiographic capabilities from the standpoint of being able to read your own x-rays
and what kind of sensor you have. So this is what he looks like inter-orally. You know, questionable.
If you want to just do a real quick look, you may not necessarily see any caries. There's a little
bit, sorry for the washed out appearance on the, there's a lot of light. This inter-oral camera is
not the best camera. A little bit of decalcification there. A little bit of white spot there.
But you can kind of see these, you know, triangles here. Kind of. So I talked to them about, you have
some interproximal cavities, some cavities in between your teeth. And here's how I like to say
this to patients. You have a couple of choices. We can either, one, leave them alone, let them grow,
and eventually you're going to end up needing a root canal and or a crown, or a crown and or a
root canal. Or we can fix them now. I'd recommend fixing them with a filling. You have two choices
of filling material. The first choice, what I'd recommend is the best choice, is a ceramic filling
we call an inlay. The ceramic is a much stronger material. It's made to a lot higher precision
and has a higher long-term success rate. The alternative to that is a composite restoration,
which is basically a plastic, which a lot of people have already. And I point out to them,
yeah, you've already got a couple of these plastic fillings. They look like they're doing fine.
In the end, once the filling gets larger, a stronger material is needed. So an inlay or an
onlay would be a better choice. He didn't really believe me that he had cavities. He couldn't
really see those dark spots. This one's a lot more visible there. And so I, you can see a couple
incipients down there. So I told him, well, I'll take some pictures once we open it up and show you
what we look like. So here's what they look like. Yeah, those are pretty obviously cavities. This
area I'd call incipient. There we've definitely got recurrent decay, or I'm sorry, broken through
the DEJ. So yeah, all these definitely warranted restoration there. But that goes to show you,
and taking pictures like this during the procedure really helps the patient to see what's going on,
I mean, you can't, unless you really look at that spot, you can't really see anything. So
being able to compare, you know, oh my gosh, this is what you look like. And this is what's actually
going on in there. These patients, it really helps to educate them. And I offer to give them these
photos, you know, take this photo home, show it to your mom or your dad or your girlfriend or
whatever. And then that can be something that markets itself for you. So here's the preps.
Now these are pretty big preps. I didn't originally think, let's go back, I didn't think I'd have to
extend that far. But the mesial and distal, I'm sorry, buccal and lingual spread of that
interproximal caries was phenomenal. So by the time I got it out, it was open way out. And then
I ended up, you know, coming through, kind of in that fashion to cover everything. So a little less
conservative than I originally wanted to be. But to get all the decalcification out of these areas,
it took a lot more opening than originally I had wanted to do.
So there's the preps compared to the pre-op picture. And there's the pre-seat, you know,
the evaluation looking at the seat and the fit. Turned out beautiful. They seat just nice. You
know, they're not prepared yet, not polished. And then here's the, you know, the delivery.
One minor concern for you, you know, this was smoothed off a little bit. We have just a little
microscopic marginal mismatch there. And you can see the margin in that area. But in the end,
they looked great. You know, I didn't quite recreate all the anatomy, the tertiary anatomy
and all the grooves that are in there. But in the end, turned out just great. So good case for you.
I told them we'd monitor these other areas. Take a look. I didn't really see anything at all early
on that spot when we had them opened up. Let's go back here. Yeah, I mean, you can see a little
whiteness, but it's not nearly as concerning as the other spots were. Okay, whoops, going too far.
All right. So let's talk about materials choices now. So basically, this is our spectrum of choices.
We've got composites all the way to zirconium oxide, and then we could theoretically do metal.
I've got a gold inlay in my mouth that's been in since dental school, so 12 or 13 years.
It's been perfect. No problems, no concerns. It's great. So that's a great choice. There are
studies, and I've got a document that I tracked down from one of the many seric doctors out there
that has comparisons of materials to tooth strength.
And when you look at it, you know, hybrid ceramics, Labo Ultimate, Serious Smart Dynamic
are much, much stronger than your natural tooth is, for that matter.
The glass ceramics are even stronger. And then, of course, you've got your Emax,
Seltar Duo, and the Suprinity, kind of the hybrid. These two are hybrid. Zirconium mixed with
lithium disilicate or lithium silicate. In the end, my go-to, if I'm going to do some sort of a
inlay or an onlay, I love these hybrids. And I've gravitated to the Serious Smart. I really like
that material. I'm not paid by them to say that. I actually have a Labo Ultimate restoration in my
mouth, which I love. But I've gravitated to the Serious Smart material. I really like it. I think
it's a great material. I'm trying to erase that. It's a great material, the Serious Smart is.
It's easy to mill. It mills really fast. You don't have to fire it. It's very strong. It bonds in
really well. Aesthetically, they look great. They polish so easy. I know a lot of us use the Vita
and the Empress. I love these blocks. They're great. Nothing wrong with any of them, honestly.
Clinical choice, it's totally up to you. What restoration works for you,
what material works for you in your hands, and is the best long-term solution for the patient
is perfect. So that's the goal. Get a good restoration that works well in your hands
for your patients. Okay, bonding protocols. Pretty simple, pretty straightforward.
Remove it from the machine, from the mill, and clean it. Very first step, and this is the most
often skipped step. I like to use isopropyl alcohol. Scrub it down. You don't want to
necessarily use water, just water, because there are oils in this milling unit. With the CEREC
milling unit, there's oil mixed with water. So you need to get that oil off of there. So clean it
with isopropyl alcohol. Try it in. Make sure it seats okay. Do your adjustments if needed.
If you're going to stain and glaze and polish, like you can see on these two restorations,
which looks beautiful, you would do it, of course, after the trial fit. Personally,
I almost never stain and glaze unless I'm doing a bridge or an anterior crown. I don't necessarily
think there's anything wrong with it. I just don't put that much weight to staining and glazing
unless there's something incredibly visible. So once we've cleaned it, trial fit, stain and glaze
if you want to. Then you have to isolate, and then we're going to prepare both the restoration
and the tooth, cement it, finish, and polish. We're going to go through each of these steps.
This is what I use. Monobond Etch-n-Prime, which is an Ivoclar product. The Adhese Universal in
the Viva Pen, which is also an Ivoclar product. And Verilink Aesthetic, which is also obviously
an Ivoclar product. I really like how these materials work together. It's a very simple
bonding protocol. This is for the restoration, for the ceramic, and of course, this is for the tooth.
This takes 60 seconds. It's a 20-second scrub and a 40-second, leave it alone.
This is a 20-second scrub, an air dry, and a light. And then you apply the cement, and we're
going to kind of go through that. Now there are a lot of people that like to use this Yellow Etch,
Hydrofluoric Acid, or Red Etch, there's some red versions as well, and Silane, and that's perfectly
fine. What's interesting though is you combine these two and you get that. So this will do
everything that the Yellow Etch and Silane does, only a lot better in my experience. So I always
go to Etch-n-Prime, Monobond Etch-n-Prime. You can kind of see it says Etch-n-Prime,
not the Monobond S, the Monobond Etch-n-Prime for my ceramic conditioning. And then here's the process.
So this, you can, this should be Etch-n-Prime here. So with Etch-n-Prime, there's a 20-second scrub
and then 40 seconds of reaction. So it still takes 60 seconds, but with the Etch-n-Prime,
20-second scrub, 40-second react, then a rinse and a dry. Rinse and dry. But the process is
basically the same for almost everything. I, you know, rinse the restoration. If you're going to
do Total Etch, which I almost never do unless it's all enamel, rinse and dry, apply the adhesive.
This is a 20-second scrub, then a light cure. I'm sorry, dry and then a light cure. So adhesive,
dry, light cure. 20 seconds, then we want to dry it until it stops moving and then a 10-second
light cure. All right, then for me, when I'm applying the restoration, when I'm putting the
restoration in, I don't put the cement on the restoration. I put the cement in the tooth
because for me, it's just a lot easier to get the restoration to seat or to hold onto it when
there's no cement on it. So I will put it in there and scrub it around a little bit either
with the tip of the cement or with a microbrush. And then I like to use the light and I put it
right on the occlusal surface and press really hard to make sure the restoration's seated.
And I'm going to cure it for a couple of seconds. And then I'm going to do the two-second,
two-second, two-second, two-second on each corner. Then, since Verilink Aesthetic has such a really
long gel phase, you can peel it off, kind of like Fuji that's half set. Peel it off. Then you can
use your liquid strip, if you use it, to avoid the oxygen inhibited layer. Then cure the rest
of the restoration. Then polish it and adjust it. And if you want to use a protectant afterward,
that's great. But usually delivery, once you've etched it and clean up with etch and prime,
with this solution here, delivery and cleanup takes me five minutes.
So, and here's the materials. Here's the adhese. Here's the etch and prime that I was mentioning
about. You can look all this stuff up online. Monobond etch and prime, much higher bond
strengths than all these. It's a great material. Good stuff. In the end, my personal experience is
this stuff works really well. But, like I said before, what works well in your hands, for your
patients, what works best for you is perfectly fine as long as it's a good long-term solution.
So here's the pre-op. Here's the preparation. Looks like they've either left some composite
or put a build-up in there. And then there's the post-delivery. I'm sorry, that's the try-in.
This is the etching with the etch and prime. So they're scrubbing it. There's this 20-second
scrub and then a 40-second reaction time. There's a total etch and a rinse. 20-second scrub with
adhese. Variolink aesthetic is applied to the bonding surface of the restoration. I'd suggest
applying it to the tooth instead of the restoration just because it's so hard to hold on to it. I don't
like these Optra sticks, but you can use that. Whatever works best for you is fine. Then the
like here, the tack. Again, I said tack it down, clean off the excess, pick it off, use liquid
strip if you want to, then polish and floss everything. And in the end, it should look like
a beautiful, natural, natural tooth. So there's my contact information. Now you got my cell phone
number. Feel free to text me if you have any questions or email or phone call, but don't spam
or send me any junk. I'm happy to help if you have questions. I think all this stuff is also
on my LinkedIn profile if you want to call or send me any information. Basically, that is it in a
nutshell. You know, I think getting back to this one. Let me hit play here again. This, I put in
monobond plus. I chose the wrong instruction sheet, but it makes sense. And if we go forward to this
conditioning step, this should be the etch and prime. So just remember monobond, etch and prime,
20 seconds scrub, 40 seconds of reaction, and then rinse it and dry it until it's bone dry.
And all this kind of greenish turquoise color should go away. So that, in a really quick nutshell,
is the basics of inlays and onlays. Again, the goal is to be as conservative as possible,
but provide a long-term, long-standing restoration for the patient. We used to only have two choices,
fillings and crowns. Well, now we have these inlays and onlays. So there's a big gray area
between where you go from filling, transitioning to inlay, to onlay, to crown. So I'd suggest we
should probably be doing more inlays and onlays, because if we can save all of this healthy tooth
structure, as opposed to, you know, getting a tooth surface wide filling, then cutting the
whole thing off and doing a crown, if we can save some of that for the long term, in the end,
is going to be a blessing and a benefit to the patient.
