
Trash To Treasure
3 followers
This build is something I often find myself doing when either I'm stuck in between a project.
It helps me clear his head.
#Upcycling #Zerowaste #Diy #Recyclingart #Sustainable #TrashToTreasure #ScratchBuilding #Kitbashing #TrashBashing #ScaleModel #SciFiModel #DIYCraft #PolystyreneCraft #ModelWeathering #PlasticModel
AI Generated·May contain errors
Video Summary
AI GeneratedAaron demonstrates how to build a custom spaceship from scratch using PlastiCard and styrene sheets. Without a pre-set plan, he focuses on improvisational design, utilizing basic hobby tools and offcuts to create a detailed model, which he names \"Wedge,\" before applying a multi-stage painting and weathering process.
How's it going everyone? Normally I'd be showing you a toy right now.
I'd be transforming into something different.
Now there's a slight change to this week's build. I'm going
to be making a spaceship from scratch using mainly PlastiCard.
I have no plan on how the spaceship is going to look.
I'm just going to cut up some PlastiCard and see where it takes me.
My name is Aaron and you're watching Terrain by Aaron.
This PlastiCard or styrene sheet
is a lot thicker than I'm usually used to.
It's five mil thick so it takes a little bit more scoring to break
and as you can see I'm just
sort of like trying to map out something
but I'm not going to really measure anything. I'm just
going to use the little squares on my mat
and just measure out with that and use the ruler
To cut straight lines.
Like I said I have no idea how big
or small the spaceship is going to be
but I'm thinking the longer of the two pieces will be the top
and bottom of the ship and a
little side note I'm making this in between building
an Ian McHugh flying boat and an
Ork submarine. I'm stuck on both
so this is what I do when I have decisions to make. I start building
something entirely different until inspiration hits me
and I can go back to my other projects.
That's a 3-2-1 block or engineers block as I've heard it being called.
I have two and they are very handy to have on your hobby desk
when doing stuff like this.
I use a couple of magnets to hold one sheet
while I glue the other sheet to the first.
Also something very handy are nail files.
Now I borrow a couple from my other half now and again.
But you can buy expensive ones if you so wish.
I just use cheap and cheerful stuff because
I hate to pay 10 euros for two fancy files
that I know will do the same job as the ones that my
other half have. Now I'm trying to be a little bit fancy here
and give the ship a little depth.
Something I've not done very often on other spaceships,
but by gluing the triangle onto the inside will give
the ship a better aesthetic look once painted, I hope.
So I'm just using the offcuts to enclose the back
or front of the spaceship, as I've still not decided yet,
and glue the next piece down,
which now gives me the basic shape of the spaceship.
So I'm thinking the slanty end is the front.
And the open bit at the back is the back that made sense to me.
But now I want to give it a little symmetry
with the front where I did the triangle.
So cut two triangles out and place them at the back like this.
And I think that looks cool with the little gap so you can see in.
Again giving it a little bit more sort of aesthetic texture.
Last year.
So I'm just going to glue that in and then take it to the next step.
As you can see I've added a little square box
and again I'm adding some small triangles
because I want a pipe running along that space
to make it look like it has some sort of function.
All that's left for me to do on this bit is add
a little bit of styrene just to enclose that
and then it's on to the next bit.
I'm going to use some thin styrene rod and use a few pieces
This is to cover the gap that's in the little triangle.
Again, this is just to make the empty space look more interesting.
A while ago, I was watching Adam Savage use what he called a notcher
that cuts square bits from styrene.
I finally found a version of that, but it's not square.
This is more for fabric, I do believe.
Now, if anyone is watching
who knows where I can buy a squared notcher from,
please let me know in the comments.
I would love, love one of them.
Just to make proper Star Wars panels,
so what I have to do is notch out two little bits and then
still use my knife just to cut the bit in between to give me a square
but I really
really want one of these square notches.
So if anybody knows where I can get one from
please let me know in the comments.
I finally enclosed a square at the top and I'm actually
I'm actually surprised it fits since I didn't use proper measurements.
Just to give the ship more of a look I'm going to add wings
so mark out in pencil
what size I'm looking for and while I
do that I think it's code word time. If you're leaving
a comment and I hope you do I reply to all comments
and hopefully one of you will be
able to give me directions to a new Notcher.
Please leave the code word in your comments
so I know you got this far before zapping to the glamour shots
and the code word is oxidize.
And that will make sense a little later on in the video.
Also please like, hype and subscribe to the channel.
It really helps push the builds to a wider audience.
If you want to help out further consider becoming a channel member.
It's just like Patreon, only on here, one click away.
Prices start at 99 cent a month
and you'll get access to the exclusive member-only builds
and you become a member of the Scratchers,
a term I affectionately call my members.
Not a medical condition that my members have.
Anyway, back to the build. Oh look, I've made some wings.
And not only wings but panels, lots of panels,
by using offcuts from the PlastiCard.
Put some onto different panels and added some little styrene rods
and stuff just to make things look interesting.
Now I will be adding some little bits from a model kit
but that will be bare minimum.
I didn't film me making the panels to go on top of panels
because it was kind of dull.
But you get the idea of what I've done
with just offcuts putting them onto a panel.
But now I'm adding those panels onto the ship.
So that's how the ship is looking and checking the watch.
It's taken just over an hour to get
to this point which isn't bad to say this is just
a little side project. There's the tube which is
from cable tidies that I'm just adding
and then I'm just adding some more panels.
Now I used Tamiya's extra thin cement
to bond the plastic card together.
I'd love to try the weld-on glue
but apparently it's not available in this country
and I can't get it imported either.
The last panel goes on the top
and now the wings onto the sides.
And that's my side project spaceship done.
All that's missing are a few greeblies from a 172 scale model tank
and I think I need to come up with a name for the ship.
I know I'm gonna call it wedge.
I didn't film me adding the greeblies on here
because there was only a few to add.
So now it's time to get the turntable out
and prime this thing
and it's just gonna be a normal bog-standard black primer.
I'm gonna do all the little pipes
and the exhaust with a sky blue paint.
Paint the pipe black
and I didn't film me just spraying on the gray for some reason.
I didn't hit record but it's going to be gray with blue highlights.
Yeah so next I'm going to try
and do some Aztec highlighting which is basically me
sticking tape down and painting it another color to try
and show the gray panels underneath.
For the top colour, I'm going
to use some US Desert Armour, don't ask why.
And I'm not going to use the spray gun,
I'm going to use this, which is a blending sponge.
Yes, you guessed it, from the other half.
Now hopefully, once I've done, I'll be able to wash
this and put it back in her box and she won't know any different.
But right now,
I'm just dabbing on the paint and it's working, basically.
I've done this technique before.
I let the paint dry and then carefully peel off all the little tape
that's on the spaceship to reveal the grey underneath,
which you can just barely see.
That's okay, that's the look that I was looking for.
It's this next bit that I really want to get to,
the weathering that I want to try.
It's a two part application, one is a special acrylic paint,
the other is an oxidising agent which gets put over the paint.
And it should oxidize and leave a nice patina.
So first the special paint goes down and I'm just going to put it along
the edges, along the bottom of the spaceship and let that dry.
Alright, I got impatient and used the hairdryer
so I'm now using the special oxidization agent
and I'm just putting that over the paint that I've already put down.
And I'll probably use the hairdryer again just to try
and speed up the process.
Well, here's a spoiler alert. It didn't work. So I obviously didn't
do something correctly and I need to go to plan B.
Okay, so the plan B box is basically weathering paints
that I usually go to in times of crisis.
So I'm just going to throw some rust down
and I'm not going to do any weathering because, you know,
it's only a one day build and I really can't be bothered.
So, yeah, I'm just going to put some rust down
and then we'll see where we go.
Probably some panel liner next.
So yep, I just decided just
to throw some panel liner down and call it good.
So next will be the glamour shots.
I hope you enjoyed this little sort of
Insight into what I do in between builds.
Not bad for something that was just
a square piece of plasticard about two hours ago.
So as I said, next to Glamour Shots,
all that's left for me to say is thank you for stopping by.
I appreciate all your support.
Please keep those comments coming.
Don't forget, if you know where I can buy a square notch from,
let me know in the comments.
And as always, keep scratching that build everybody.
Thanks for watching.
Stop
the
music.
Um, quick update on the little sponge
that I borrowed from the other half.
I tried washing it out and it stained the sponge
and made the sponge even bigger than
what it was and it's still retaining water.
Oh my gosh.
Um, so top tip, um, don't wash it out because,
look, I'm just going to hide this.
I'm going to, bye, bye now.
Where the heck did I put Plan C box?
