306. Trimming/Assembling a Bamboo Handle Teapot with Hsin-Chuen Lin 林新春 提樑壺修坯接合示範

Soul of Siberia
114 followers
1 Video View·Dec 1, 2022
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
www.mypots.net
Follow me on Instagram: hsinchuenlin
Okay, I'm ready to trim and assemble them together.
Like I told you in my previous video that I usually make the lid a
little bit wider so you can see that it's not a perfect fit yet but after
trim they will fit nicely and perfect. I will first trim the foot and then flip it
over upside down and then trim a little bit here and remove some clay.
Okay, for general trimming I usually use my number two which is shorter so it
doesn't vibrate or get easy to get chatter and mark.
Okay, so I first trim the foot. Okay, that's right and then flip it upside down and trim the rim.
So now the lid can fit tightly here so I could even trim the lid right on top of the body.
So far I was using the number two trimming tool to do most of the trimming job but to make a
knob look nice I'm using my number three so it will go and fit right under here.
So we'll cut a nice groove so the finger is easier to grab on the knob and pick it up.
Okay, so done with the knob trimming and I'm going to put some chattering texture right here.
So done with the trimming.
I'm ready to assemble the spout.
Okay, so now I'm trying to fit the spout.
I'm using my number seven knife trimming tool to shave up the spout so it will fit perfect.
Okay,
so
okay so there's one other trick that I want to show you.
So after I shave most of the clay off there's still a little bit of gap.
I usually get a hacksaw blade with a little teeth there so I'm just using the little teeth to
remove some more clay so it's like a fine tune so that the joint will fit better.
Just use the teeth of the hacksaw blade to remove some of the clay.
So
the spout is the most fitting and I'm going to use the needle to draw
along the joint so that I know where I need to punch the hole for the spout.
So
sorry I just found out that my camera on my iPhone is full with the storage so I have to
free it up. So I sum up when I joined the spout that I'm missing in the video. Now the spout has
been attached. So anyway just to show you the final product that I'm making because I already
missed the video that I thought was shooting. Okay, so now I'm ready to attach the handle
for the bamboo. I just rolled out the coil and then bent it and let it dry a little bit.
So I'm applying slip over the joint.
I'm putting a drip of water there right by the joint.
I'll maybe use my stamp to compress the joint.
So
this will be the teapot look like after
the bamboo handle. So it's a little bit bigger
but after fire it's going to shrink a little bit more so it will fit nicely there.
So this is the finished teapot with the bamboo handle.
What I did is after I carefully cut out the spout and then I punched holes
right there where the joint is on the inside. You won't be able to see it now.
And then I get a sharp knife and just cut out. So the spout is a little bit of an angle
on your angle. The left hand side is a little bit lower than the right hand side.
So because I threw the spout so the spout during the fire it's going to turn the way you
pour it the clay is manually so it's going to turn the clockwise way. So if I leave this part
a little bit higher this part lower and then after fire they will twist back so it will be straight.
So that's the reason why I cut at an angle.
This is the finished bamboo handle teapot with a lot of rolling roller texture on it.
Okay thanks for watching.
