198. Trimming a Mug in Detail/Close-up View with Hsin-Chuen Lin 林新春

Soul of Siberia
114 followers
1 Video View·Dec 4, 2022
To see or buy my finished work, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
http://home.comcast.net/~hsinchuen/site/
www.mypots.net
Today I'm going to show you how I trim the mug.
And I'm going to show you the close-up view too. So you can see how the tool, my trimming tool,
cuts through the clay and how I position my fingers together. Okay so first I'll get my clay stick
on the wheel head.
I usually use water to stick my small part on the wheel. But sometimes if you worry about the
clay might fly away, you might want to add a coil on the corner so that it doesn't fly away.
But by doing so, I can easily trim. If I want to trim the bottom corner,
then there's no clay there to block my tools. So that's why I usually like to
get my clay stick on the wheel head, right on the wheel head.
So most of the time I'm using my standard steel trimming tools, number two. I use the number two
the most of my job for the removing clay parts. By holding the tool very tight, you can see that
I'm holding my tool using my thumb and finger to grab it tightly. I can change the side of the
trimming blade by doing this to get to the corner of the foot. And by switch side, so I get to use
this part to trim. So this is the number two trimming tools. And also I want to try to flatten
the bottom. So the very first cut, I will start at this position. And you can see that I have my
left thumb holding my tool to stabilize it. And I cut a little bit deeper so that my tool is not
sitting on top of the unevenness. So that I will be able to cut it flat. And after cutting it flat,
I see that all my fingers kind of try to help each other. And just by using the corner
of my tool to cut a small indent here. So this will be my foot. And then I'm going to remove
the clay in the middle. And for removing clay from the middle, I usually start in this position.
You can see that I'm using the corner part of my trimming tool. And start it from the very,
very center. And go dig in. And then slowly move out my tool. That's one cut.
And two cuts. I remove a fair amount of clay out of it. And three cuts. So after I
remove quite a bit of clay, I want to check the thickness by simply tapping the bottom.
And this sounds to me still quite thick. I will keep on going. All right, check it again.
Okay, this sounds a lot more better. Kind of like a drum. Thinner. And then I'm going to refine
where I cut. I refine the corner. And change the direction of my tool. So this is 90 degrees.
I'm going to use the 90 degrees to cut into the corner of the foot. So that corner here
is much nicer because I'm using the 90 degrees of my trimming tools. And then
I want to round the corner here. I don't want the corner too sharp. So hold my tool at an angle.
Round it. This part has been taken care of. Now I want to refine the other part of the foot.
You see that I'm holding my tool tight, resting the tool on my left thumb.
And also round the corner here. Okay, and then I'm going to undercut by using the corner
of this tool. I cut a little bit deeper here to refine it. And leave a little small line
on the bottom corner. Little line here. So that's the foot. And then I'm going to
cut the surface nice and smooth by spinning my wheel a bit faster and moving my tool slowly.
especially the bottom of my foot. To round the bottom of my foot. Because this is the
tableware. You don't want the bottom too thick to scratch your table. So I use that to burnish
the foot. After that I'm using a stamp. This is made out of oxhome. Years ago I had people
carve it for me in Taiwan. You can use a porcelain to carve yourself. Put your logo
or your initial. So this is that. I have people make it smaller so that it just fits right on
the foot. So that I don't need to sign my name. A little bit more of the trimming mark
if you don't want it. You can spin your wheel fast and you can remove the line, the trimming line
fast and slowly moving the trimming tools. Spin the wheel fast. Now the surface looks
smoother and nicer. And if you want to trim this part here there's a little curve.
I usually use my number five trimming tools. So you see that there's a curve fits right in the
curve there. If you want to trim. Let me do the demo here. I'm gonna trim the curve so that my
tools can reach the very bottom. As I told you that that's why I want to use the water instead
of a coil to hold my pot. The whole piece is done. Finished trimming. This is the way I
try to pick it up from the wheel head and spin the wheel and then twist, spin and twist.
So this is the piece that finished trimming. A little bit rough on the edges.
Just use a sponge to clean up the rim. So this is the piece that is done trimming.
All I need to do is add a handle here. You will have to have them on. Okay thanks for watching.
