DIY Off Grid Cabin Build Episode 16

The Woodhaven
54 followers
1 Video View·Sep 14, 2025
In this video, I start building the DIY trim for the cabin using 2x4s and 2x6s.
If you are planning to shop on Amazon, consider my Storefront:
https://www.amazon.com/shop/thewoodhaven
Check out Amazon's Hottest Deals (updated hourly):
https://amzn.to/3K5ybkn
Check out Deep Discounts on Open Box Tools:
https://amzn.to/3MeYZ3h
DISCLAIMER*
This video and/or description contains affiliate links, which means that if you click on one of the product links, we may receive a small commission at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
Music:
YouTube - Audio Library
Bensound - https://www.bensound.com
All right, so I'm gonna be making the trim
For the cabin, you know on the corners out of two by lumber a bit two by six
And I've got two by fours and I'll I'll put the two by fours up
Like this
So that'll give me six inches on one side six inches on the other it's not exact but it's close enough
But in order to do that so that it looks halfway decent I need to first cut the
edge off of each of the two by sixes and two by fours and I need to
Create a notch
That goes all the way down or rabbit
Seven seven or three quarters of an inch
deep and high
So that the siding can fit up underneath it, I think it'll look better that way it'll give me a little bit of
wiggle room also
if the
trim and the
And the siding is not exactly square that will just you know help to hide that
So that's what I'm gonna work on today
So, let me get started
All right, so what I'm gonna do this on the table saw so I need to lower my blade so that it's 3 quarters of
an inch
actually, I want it to be just slightly proud of 3 quarters of an inch because I
Want it to be snug but not so snug that any kind of a flaw in the siding will not be able to slip under it
Okay, so I've got the blade lowered so that I can just
feel the tip of the blade above
This so 1 by this is 3 quarters of an inch high. So this makes it really easy to set my blade
And
Also set it this way so that this is flush
With the outside of the blade not the inside
And I do need to make a small adjustment
Yeah, so that's just proud so that set up should work and I'll run just a scrap piece of 2 by 4 through there to see
How it works?
All right, let's see how it lines up
so it's just
Just clipping that
So I need to take a little bit more off that way
And it's the same here
So, let me make a minor adjustment and we'll try again
Alright, let's try that
All right, that looks good I'm gonna go with that
All right. Let's see how we did
All right, I think that's gonna work so I'm gonna go ahead and keep cutting the other boards
I'm gonna have them set
like this
and then I can
clamp them together and
then when I
attach those probably attach them with
galvanized ring shank nails
It'll look you know like smooth transition and I'm gonna stain these black so
You're not gonna be able to see the grain
So the grain, you know, it doesn't have to match up perfectly
But
Disconnect that you can see what it's gonna look like so I'll have my
My rabbit here and a rabbit here and this will be the cabin
So it'll be able to accept the siding like this and then the siding like this
So that's how I'm gonna make my trim
But there's one more thing that I need to do
Because I trimmed this
You know both of these pieces so that they would have a nice, you know flush fit there. I've got a sharp corner here
So what I need to do on each of the two by sixes is I want to take my router
I want to route this sharp corner to make it, you know
Nice and smooth as if it were a normal two by six
So once I do that
Then I'll be ready to
Use these as trim
I've got one flat piece that's going to go at the eight foot mark. So it'll be in the center of the cabin
So all the siding will come this way and then this way
so I had to
Take one and make a rabbit on both sides
Okay, so with the two corners and my centerpiece and I've got all of my
tongue and groove
Siding slats. I should be able to
Put to trim out and put together the front of the cabin
So what I the only thing I have left to do on these
is stain them black and
I
Guess I need to build the corners out as well
But I'm gonna do that down at the cabin I've thought it through and I've tried to
Figure out in my head how I would cut, you know those compound corners
with
With having these things put together and I just I can't come up with a good easy scenario
So I'm gonna cut those first and then put them together down there. It's not going to be a problem
And I'll wait until I cut them and put them together before I stain them because I
Don't want to stain them and then cut them and then have to stain them again
You know, I don't want to have to go through any of that
so anyway, that's
What I've got for this week. I know it doesn't look like much but
This is the kind of thing that you got to do behind the scenes
