How To Make A 3D Egg Costume

The Stone Cube
31 followers
4 Video Views·Nov 3, 2022
This is an egg. This is how to make an egg costume. Start by laying out some paper.
Mark a few dimensions and start drawing the egg. Just half of it though. Fold it over and then cut
it out and you'll have a pretty symmetrical egg. Next grab a sheet of two inch pink insulation.
You should be able to find this at pretty much any home improvement store. Take the template
that you just made and use it to trace out the egg on the pink insulation. I used a combination
of a hack saw and a keyhole saw to cut my egg out. Now it's time to cut out the center of the egg.
This first line is just the external boundary for the next layer and then the line in from that is
where you'll be cutting out the center. The first line isn't totally necessary but it gives you an
idea of how much overlap there will be. After that it's a matter of cutting out the pieces,
tracing them so that the opposite side will be pretty identical. So during this whole process
I tried quite a few different knives and saws and whatnot and I found that even though the
keyhole saw was the messiest it was actually the easiest to control. After you cut out all the
pieces to one half of the egg it's simply a matter of tracing each piece and cutting them out so you
have mirror images of the other half the egg. Next it was time to glue up all the pieces.
I read somewhere online that when gluing this type of foam together contact cement would be
the best option and it worked great, almost too well. The contact cement actually reacted with
the foam in a way that it sort of melted it. The area where the contact cement was applied
turned kind of gooey. When you put the two pieces together they kind of just melted together and
it actually formed a pretty tight bond. The only drawback is though the surface kind of bubbled up
so it wasn't smooth and flat like it used to be. Next to fill in between the steps that each layer
of the egg creates I took this great stuff expanding foam and just ran it along each
corner. This just helps fill in the void since I'll be shaping the egg later.
I found in this situation the hacksaw actually worked the best. Now there might be a way easier
method in shaping this kind of foam. I found that the tools that I had this just worked the best and
it was relatively easy. I don't think there's a right way and a wrong way to do it. Now here I'm
gluing sandpaper onto a scrap piece of MDF to make a simple sanding block. After a bunch of sanding
it turned out pretty smooth but there were still some gaps as you can see. Also it really wasn't
the shape that I was looking for and I figured out that it just needed another layer on each side of
the egg to really get the shape so I went ahead and cut two more layers. Now there are many ways
to do this next part and this is just how I did it. It's paper mache. So you take some flour, a
little bit of salt, and some water and mix that together and you got this kind of paste that you
use with paper and when it dries it hardens obviously. You might have done this when you
were a little kid. What I did was I added some shredded paper to the mix and it kind of made
this paste that I could form a little bit better and it was pretty thick as you can see. Now the
consistency of this, the only way I can really describe it is like a spitball. So I put on some
rubber gloves and just took this by the handful and started spreading around making sure to push
it in the cracks and really give it a smooth surface when I was done. After that had dried I
took a sanding block and just knocked down all the high spots. Then I went and marked and cut out
locations for my arms, my neck, and my waist to penetrate through the egg. This step was a little
bit tedious because you would cut a layer, check it, and cut another layer, and check it. I didn't
want to cut too much and kind of lose the whole shape of the egg so just take the step slowly.
And once I had it how I liked it for the first side then I just simply transferred those marks
onto the other half and cut them out. And don't forget to cut out a little bit extra for your
neck. This will allow your chin to move up and down and sideways. Then it was on to another round of
paper mache but this time I did not add the shredded paper into the mix. I simply cut out
strips of white printer paper and laid them across. This layer further smoothed out the egg
and gave it a somewhat uniform texture. You can see that it's not exactly smooth and that was
okay with me. I was kind of crunched for time and this was the best I could do in a week.
Plus I didn't want to invest too much time into it because the odds of some drunk person
coming up and trying to punch through the egg were pretty good. As you can see this was my first time
attempting sculpting of any sort with this kind of foam. Finally the last step is to add velcro.
To attach the velcro I just used some spray adhesive and again I ran into the problem of
the glue melting the foam. I just want to emphasize that this egg is by no means perfect but hopefully
you learned something even if it was just how to make a larger sanding block. I had a lot of fun
with this project and it was kind of messy but at the same time it was a lot of fun to do.
Hopefully you enjoyed it and hopefully you're inspired to make something of your own.
Thanks for watching!
