How To Install Ductwork In A Basement DIY Finished Basement Renovation

The Stone Cube
31 followers
21 Video Views·Nov 3, 2022
Hey everybody. All right.
So I finished up the fire blocking for the most part along the perimeter of the
basement. Now today I'm going to move on to the HVAC.
I'm going to add a couple of supply lines and then a couple of return lines.
I've actually already started. So up here,
this one I've tapped into the main trunk and I've got it feeding over here and
that's going to supply some conditioned air into what will be the bathroom.
All right. And then I've also added this one, this middle guy here.
Actually tapped in on the top and then it tees off.
So the one T comes over here and that supply will supply part of what will be
like the wet bar dining room area of that the basement.
And then the other side of this T you can see kind of drops in right there.
That's going to supply part of what will be the living room area.
So I've already done a few of these things.
I've worked out some of the kinks since this was my first time running my own
ductwork and I thought I'd do another supply line.
Okay. So the same thing,
I'm going to T come off of this with a T over here in between these two lines
and I'm going to do the same thing.
So I'm going to run another supply that way and it's going to feed another line
into the living room area and then I'm going to come across this way and drop
another supply into the wet bar dining room area. All right.
And then after that I'm going to expand this main trunk by four feet so I can
tap in another two lines.
One line is going to run that way and it's going to feed what will be the
office.
And then the other one's going to tap in and feed what will be the workout area
right here. And then I'll add a couple of returns as well. So enough talking,
let's get after it. All right,
so real quick let's run through the tools and the items that I'm going to be
using today. So we've got our 10 snips, so we've got a right cutter,
straight cutter and the left cutter.
You could probably just get away with a straight cutter right here and be
totally fine. Then I've got two drills.
I just have them because I have two different bits in each one.
You could just get away with one though.
So I got the hex bit and then I got just a standard Phillips bit.
I got a tape measure here, a knife,
something to mark out the ductwork, a straight bladed screwdriver.
We've got wood screws for screwing in the duct supports.
And then these are the self tapping screws with the hex head that you use to
connect the ductwork. And then after I connect it with screws,
I like to follow up and just tape it,
tape all the seams with that foil tape. And then,
Oh, we got the crimper. I'll show you where to use that.
This was like 20 bucks. I just picked it up. Oh,
and then probably most importantly, because the ductwork tends to be really
sharp, especially after you cut it, we've got some gloves,
so make sure to wear gloves.
All right. And this is called a starter collar, I believe.
And it looks a little bit funky,
but basically this just tucks into here,
a box top. All right.
And then it's going to sit down this way into the new hole that you just cut in
and then these fins,
you're going to reach from the inside and you're going to bend these fins back
and that's going to hug the ductwork right there.
So then this isn't going anywhere. All right. So just like this.
All right. So then I put a couple of screws in here and then one on this side
and then I'll come around it with the foil tape and just seal it off nicely.
All right.
So one thing that might be missed if you're not really thinking about it and the
way that I like to go about this is I work from the source,
the air source out to the vent in the ceiling.
So in my case,
the air is going to come out here through the trunk and it's going to go this
way and it's going to go this way.
So what that means is we've got a crimp side right here in the new piece
is going to go over the, I guess the old piece. So the,
the every new piece that you put on, say,
you got a 10 sections of this straight piping.
Every new piece is going to go over the last piece that you installed.
So in this case I'm, I have this crimp side right here.
I got my new piece. This is going to overlap.
You get the idea. This is going to overlap that piece.
So if you can already see the problem, we only got one crimp side.
So that means I have to add crimps to this side because on this side,
another new piece is going to come over here and go over at the top of that.
And that's what this tool is. Basically it's just a really crappy scissors.
So it's got these five teeth and there's enough space in between them that when
you squeeze it together, it crimps it.
So all you do is just put it on the edge and squeeze it. All right.
So just like that. And I'm going to go all the way around.
What that does is it just creates a little bit smaller radius around here so
that the next piece can fit over the top of it. All right.
So now both sides have a crimped end and we can slide our new pieces on top of
that. All right.
And then we just add a couple of screws to each seam and then I'm going to tape
around each one.
And that right there is a hundred times easier than doing it up on a ladder in
between the different floor joists. So that probably just saved me a half hour.
No lie. All right.
So I just added another five foot section of duct work on this side.
Simple as just adding another support.
And then I just threw a couple of screws in there and taped around the entire
seam.
So now I want to get this a little bit closer to the exterior
wall. But if I put another five foot section, it's going to be,
I think a little bit too close because we're planning maybe some kind of a built
in over here. So I am going to split it.
I'm going to cut a five foot section, not quite in half.
I'm going to put three feet on this side and then I'm going to take the other
two remaining feet and add it over on this side.
So that gets me a little bit closer to the exterior wall over in like what will
be the wet bar kind of area.
So let me show you how to cut some duct work. All right.
So I've got another five foot section of this six inch round duct work
and I'm going to try to cut it right about here.
So first take tape measure and I just like to use a red Sharpie
and mark a couple spots around the outside
of where you want to cut. So in my instance,
let me double check actually. Okay.
I just had to double check the one I previously ran. All right.
So I'm going to cut this at three feet.
So it's going to leave me two feet on this side remaining.
So just make a couple marks along the outside.
This is, it doesn't have to be perfect,
so just do your best. All right.
And then just play connect the dots. So again,
I think it helps if you kind of hold your hand steady and then use your other
hand to roll the duct work. Just like that. It's pretty close. All right.
So then this is definitely an instance where you're going to want to put some
gloves on and then I've got my straight cutter and then we're just going to kind
of open this up a little bit, not too far. You don't want to kink it really,
but just give you some working space and then just cut right along it.
I find that I'm right-handed so I'm going to cut with my right hand and I use my
other hand to kind of pull it straight up and then this other side will
naturally still want to curve down.
And then I get just about probably a little more than halfway.
Turn it around and then come at it from the other side.
All right, now we got two pieces and then right away,
let's go ahead and just connect them together and the other side.
So now you'll notice that on this piece,
we're going to be connecting up here to the five foot section that we just
installed, but this piece has no crimps on either end.
So it doesn't really matter which end you put them on,
but we've got to add some crimps.
So take the crimper and just proceed along the outside.
So we got one crimped end, one straight end.
This we got the factory crimped end and the straight end.
So now we can take these two pieces and go ahead and install them in the
ceiling.
So we have the factory crimped end on this side and we'll put the straight end
on that side.
But it was just easier to add this other crimp to this other side while we were
on the ground.
We'll have to use this later on when we put like a little elbow on it and then
put the ceiling grill in.
All right,
so I just got done putting that three foot section of duct work right above me.
And for the time being, I'm just going to put an elbow on it.
Until I set my grill at the specific height that I need,
I'm just going to direct the airflow straight down.
So this is an elbow you can pick up at any of the big box stores and right now
it's straight.
But if you look at like this section in particular,
you can see that right here there's a fat side.
And then if you kind of follow that around,
you'll see that it turns into a skinny side.
So to get a 90 degree elbow,
all we got to do is connect all the skinny sides together.
And how you do that is you just twist this around.
All right,
twist it around until all the skinny sides are touching.
Do your best not to reach too far in because sometimes there can be some sharp
parts and you would slice your hand open on the outside section.
So this section and this section, just keep your hands, you know,
just pinch it on the outside.
You should be fine or be smart and put some gloves on.
So we're just going to twist this around. That looks pretty good. All right.
So there's our 90 degree elbow and I'm just going to connect that.
Like I said,
on the end of the duct work that I just got finished running and for right now
I'm just going to put some foil tape on it.
And that should hold it in place for right now. So let's do that. All right.
I'm just going to follow up with a little piece of tape just to keep it in place
while I build the rest of the basement. All right.
So currently I don't have a support at the end.
And I'm going to want one eventually,
but until I know exactly where I want this, you know,
I don't know if this needs to go a little bit higher or if it needs to sit a
little bit lower. So until I know that I'm not going to put a support,
but just note that you will want to support at this end.
So all of this duct work,
this three and a half feet isn't just cantilevered over the top because
eventually I'll probably say a little bit,
put a little bit more pressure on the drywall on your ceiling and you just don't
want that. So you're going to want to add a support at the end.
All right. And just a little bit different angle on this.
First thing I did was I added this piece across there.
That's just giving me something solid to screw these two screws into really
locks in this end. This isn't going anywhere.
I know before I said that you're going to want to support here. It wouldn't hurt.
But now that I've got this locked in down here and I've got this support over
here this three feet, that's not going anywhere.
So it's up to you if you want to add another support. Again,
that's not going to hurt, but I don't think it's completely necessary.
So I had this piece in there so I could screw that in there.
And then I added these two little blocks on the side because, um,
I think the grills that I picked up,
the two mounting hole screws are on the ends of it.
So these two blocks give me something to screw the grill into later on.
But yeah, that's pretty much all there is to it.
I know that this isn't completely level all the way across, um,
just because there's a slight angle coming down.
So it kind of slopes down as it moves this way. Um,
but for sure on this, this front lip right here,
that's a half inch difference. So that gives my drywall,
which is a half inch drywall somewhere to bump into.
It's going to be nice and flush there and should finish up pretty nicely.
All right.
So when you go to the store and you want to pick up another section of the
trunk, like the main line of the duct work, it's going to come in two pieces.
So, uh, I already have one of the seams together,
but basically it comes in two L's.
So this is a piece and then this is a separate piece.
So right now I still got to connect to this seam and I'll show you how to do
that. The easiest to be pushing down on the seam.
So right here we have like this little U slot and then we have this,
uh, just bent over a piece of the duct work right here.
And then it's got these little dimples in it.
So it's got these dimples right here. So there's one, there's another one.
And these dimples are what keeps this piece in the U section of the other
piece. So it's really easy.
Just put that slot into the U shaped of it of the other piece and just push down.
You might hear them snap like that.
Just work your way all the way down.
It's kind of double check. Just make sure that these,
this inside corner basically is lined up with the other side. All right.
And then you're going to want to pick up a pack of these duct hangers. Um,
look like this. Basically they're just a little L shaped like that.
They're a little bit different than what the, uh,
builder installed.
I kind of like what the builder installed a little bit better,
but I couldn't find those at a local store.
But basically this is going to sit right there.
So I'm going to put a screw in right on this bottom one and then screw up to the
floor joist.
There's works a little bit better because it is this entire strap and then it
can come down and kind of catch the underneath of the duct work.
But these will do. And just to be consistent,
there's about an inch gap from the top of the top of the duct work to the
underside of the floor joist.
So that's what I'll space my new duct hangers at. All right.
So now I'm going to just hold this section up so that I can mark on it where it
comes in contact with the floor joist.
So that way I can bring it back down on the ground and install the duct hangers.
Just makes it a little bit easier when you're working by yourself.
I can transfer these marks to the other side on the ground just by measuring.
So again, this part is going to be against the floor joist.
So I'll measure an inch down from there, approximately.
All right.
And then I can just line that up with the edge of the duct work and I know right
where to drill it in. So I'm just using a self tapping screw.
Three quarters of an inch long.
That's all there is to it.
So this one's a little bit tighter quarters.
So I've got this one that I just installed coming up from the top.
And so I got a double elbow here and then there,
and then that's going to be right up next to this existing one right there.
That's coming out the side. I'll show you that. All right.
So that's this guy coming out the side.
So you can see the new guy coming out the top and up and around and right there.
So now I'm just going to add another five foot section onto that and get it to
approximately the center of this room.
All right. So now that I've got all the supply runs pretty much wrapped up,
I'm going to move on to some of the return lines. So right above here,
I've got my main return trunk and what I'm going to do is utilize this stud
cavity right here as one of the return drops.
So what I've got to do first is cut out this top plate.
So right there and then right there.
And then I'll cut a hole into the bottom of this return duct and then I'll put
some of this blue,
it's called thermal pan on the backside of that space since that's not going to
get gypsum board on the backside.
Align the whole backside of that stud cavity with a thermal pan and then once
the gyp board is placed on this front side,
that a stud cavity is going to basically act like a piece of ductwork.
So then the air can pull in from the bottom and move up that stud cavity and
then get returned through the ductwork. So let's get after that.
All right. So that wraps up this one.
We've got this stud spacing that's going to act as the return line.
Once I put drywall on here,
then that will be enclosed and that's going to pretty much act like a piece of
ductwork drawing air in and up in through the return line.
So that was fairly easy. I'll probably move this wire,
just run that elsewhere. But other than that,
it was just putting this thermal pan on the backside and then using some of that
foil tape, a couple of staples just to kind of box that all in nicely.
And then here on the bottom I put one of these,
I don't know what it's really called, but it's like a grill receiver basically.
It's got a little half inch lip here.
So the drywall is going to come right along here and be flush with that.
And then it's got a couple of mounting holes on either side for a grill to mount
onto. So that one's all wrapped up. Now, if we come over here,
the other side of the house, I've actually added in two more.
So there's our first one down there.
Here's our main trunk return line and I've punched a hole in the top of that and
I've branched off both ways.
So I've enclosed this joist spacing with some more of that thermal pan.
And then I'm going to add, well, I have added this return right here.
So it's going to utilize that stud spacing,
put another grill at the bottom so it can draw air in from the bottom and up and
through all the ductwork. So that one's in there. Again,
this one's going to have a drywall on both sides.
So I don't need to run the thermal pan down the stud spacing really at all.
So that one's there. Come over here in this other room, the office over here.
So there's the main return line again,
came over here and dropped another one down.
Utilizing this stud spacing as well, put another grill down at the bottom.
So the idea is that if we look across here,
I've got my supply line coming over here.
It's going to drop conditioned air into the space and that's at the ceiling.
So I wanted my return down at the ground level so that hopefully it draws air
from the ceiling down below,
kind of conditions the whole space and heats and cools the entire space evenly.
So if we look at this a little bit closer,
I just use that same thermal pan to enclose the joist spacing.
And then they actually make a little end cap for this specific task that you can
do. Just put it in there,
throw a couple of staples in there and then I just went around everything with
some of that foil tape. So it's pretty straightforward.
It does take a little bit of time, but it's,
it's really not difficult work at all. So yeah,
that's pretty much all there is to it.
Now I realized that this was a little bit longer of a video,
but I guess I just wanted to take you through all the different steps and
scenarios that I've ran into in my basement project.
And maybe you can apply some of those tricks to your own project at home.
If you enjoyed this video,
it would be awesome if you could hit that like button down below.
That just really helps me grow my channel.
And it also tells YouTube to pass this video on to some other people to watch.
And while you're down there, if you feel that I've earned it,
go ahead and hit that subscribe button as well.
That way you're notified every time I release a new video. Again,
I really appreciate you guys sticking through this whole video and until next
time.
