200. Trimming/Fitting Nesting Bowls with Hsin-Chuen Lin 林新春

Soul of Siberia
114 followers
3 Video Views·Dec 7, 2022
To see or buy my finished work, please visit my ETSY shop:
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen/videos
To learn more about my back ground, please visit my Website:
http://home.comcast.net/~hsinchuen/site/
www.mypots.net
Okay, in this demonstration I want to show you how I trim my set of nesting ball
that they will fit together. This one I already trimmed and you can see that it's fitting
inside of the ball. It's about the same height, a little bit taller, about the same height.
This one already trimmed and this one, the largest one, I already trimmed too
in my previous demonstration video and this one is not trimmed yet.
I try to let it fit inside the ball and you can see that it's a little bit taller.
About a quarter inch taller. So when I'm trying to let it fit inside the ball, I will need to
remove more of the clay on the foot so that they will sit on the same level. That's how you get
your nesting ball. I will show you after I finish trimming this one. I will show you how they fit
all together. In my previous demonstration, I already showed people how to make the nesting
balls by using the measurement sticks. I don't remember the number of it but
look through my video list. I think the video is there. Again, use the water to stick the ball.
Tap center and so that the ball is sticking on here.
Again, if you're worried about flying away, get a clay coil to secure it.
First, at the beginning, as I told you before, I usually use the number two trimming tools.
Do the most of the trimming job. By the way, before I keep on trimming, since my clay is still
thick, I want to show you a couple ways of doing the chattering because one of the viewers
she said that she can get a chattering going on her trimming tool that she bought from me.
So I have to show you. Even the number two trimming tool, this is the shoulder one,
the shoulder one. Even using number two, you can also get the chattering going. This time,
I'm going to hold at a different angle and now I stop the wheel. You can see that
since the clay is a little bit too dry, my cut is not getting deep enough.
If you want to get deep enough, you can re-wet your surface. Get some water to go into the clay
and you will have a deeper cut. The idea of doing the chattering is that if you want to get a
chattering, you need to have your tool at a certain angle so that the clay can kick back
your tool. That's how you get a cut. You want to hold the tool a bit longer so it's jumping. You
want to hold the tool, not holding here on the very far end. You want to hold it longer so
the tool vibrates. Even if your blade is kind of stiff, it still vibrates.
That's the chattering from one of the tools. Now, this is number two. You can get it.
Now I'm using the number one. It's easier to get. The number one, you can cut it deeper because
this part is longer so it vibrates more. On this part, I want to show you if I hold it a different
way, I can get a different type of chattering. I'm still holding the tool until you see that
the tool starts to get some sound. It's a straight type of chattering mark.
The chattering mark, you can see that it's chattering that way.
Almost the tool that if you hold at a certain angle, you can get a chattering mark. Even this
tool, you can get it. That's a different texture on one piece.
Let me clean up. There's so many textures here that it's hard to see.
Let me remove that texture. This is my number four trimming tool. You see that many, many
chattering textures. It's very, very beautiful. Let me try number five. Let me remove it again.
This is my number five trimming tool. It's just a tip, but you can still get the chattering going
on. It's very tippy. All you will get is just little dots, but you can still get the chattering
going on. How you hold your tool is not that you cannot get any chattering mark going on.
It's how soft you clean, and how you hold your tools, and how fast you spin your wheel.
That's all the factor that you get your chattering mark. Once you get a chattering mark,
if you want to remove it, you have to cut it a bit deeper.
You have to hold your tool tight, firm. Back to my original demonstration that I want to
make nesting balls. I'm going to trim the ball. I told you that I will remove quite a bit of clay,
at least a quarter of an inch, that much clay off, so that it's sitting inside the ball.
the sound is caused by the vibration. The vibration causes the sound, actually.
If it is getting thinner, the pitch will sound higher because it vibrates more.
lightly, spin the wheel faster. Move my tool slowly. My surface will be nice and smooth.
Now, I put the chattering mark back. For the whole set, it's the same that I will have
smooth the rim using a sponge.
Like I told you, I was trying to fit the nesting ball inside of this ball, inside of a larger ball,
ball inside the ball, and then this is the third one.
So, it's a nesting ball, and you try to measure the height, and then you remove clay so that they
stay inside the ball, like that. It's a set. You can make up to six, eight pieces
that they can fit inside.
