How To Make A Light Table for Drawing

The Stone Cube
31 followers
4 Video Views·Nov 3, 2022
A friend gave me this drafting table and I wanted to use it as the base for my light
box.
To start I picked up this can of frosted glass spray paint and a sheet of plexiglass and
sprayed that and set it aside.
Next I took measurements of the tabletop.
For this light box I wanted it to sit on top of the tabletop and kind of wrap around the
outside so it acted like a sleeve to the current tabletop.
I wasn't going to attach it with any screws or nails or anything like that so if I ever
wanted to pick this light table up and move it I could and I think you'll get a better
idea of that in a little bit.
I just used glue and brad nails to tack it together then I came back and pre-drilled
and put screws in.
Here you kind of get the idea of the box sliding on top and around the tabletop kind of like
a sleeve.
So the next thing was to make supports that would go across the bottom of the light box
and hold it at a consistent depth on the tabletop.
These spacer blocks represent the top of the table and then the support goes in there and
I'll screw it in from the side.
So the actual tabletop will sit on these supports while also being wrapped around with the box
if that makes any sense.
I did a test fit and it was a little snug so I just hit it with a sander and it fit
on there nice and tight.
The drawer still opens and the whole tabletop still tilts up.
Next it was time to work on the drawing surface itself.
I kind of just began by laying out everything where I wanted it.
Next I had to take the quarter inch melamine and trim it down to size so that it matched
the size of the plywood underneath it.
Front to back I centered the plexiglass on the tabletop surface and then measured in
maybe three or four inches and this is where the plexiglass will sit.
So I can draw those lines.
Once I got three sides I just matched up one on the corner and then I could draw the fourth
side.
I drilled a pilot hole and began cutting that out with a jigsaw.
Then I set the plywood down and laid everything in place and did a test fit and it turned
out that I needed to sand it a couple times to get it to fit in there really nice and
I finally got it.
The next step is to line up the melamine and the plywood and then trace that hole that
you just cut out.
From there I marked a half inch in on all four sides and this is the line that you want
to cut out.
This provides a lip for the plexiglass to sit on as you can see here.
Next I made a simple box for holding all the lights.
Now the depth of the box isn't crazy important but keep in mind that the deeper the box is
the more dispersed the light will be once it hits the surface of the plexiglass.
It will give you a more even spread of light.
So I made the box and then I attached it to the plywood.
I kind of went overboard with the screws.
This hole is for a pencil so that I can pop out the plexiglass should I need to.
I didn't know how well glue would stick to the melamine surface so I just attached the
melamine to the plywood with a couple brad nails.
It should just stay in place.
Now I don't know about you but I enjoy using Bondo so I find excuses to use it in my projects.
This was just to fill the nail holes and kind of form the corners so that they would look
pretty nice.
Not just like two boards butted against each other.
It's not perfect but it's fine.
And a thick coat of white paint should hide some of the imperfections.
In essence I made a box and so I wanted the tabletop surface to hinge on a point and so
that I could open it up and there would be a little bit of storage underneath it.
And in one corner of the tabletop was just a tiny bit warped.
So I used this little hook to secure it down flat.
For the light I used a strip of dimmable LEDs so I had control over the intensity while
I was drawing.
You can cut these LEDs every three and then you connect them together with these little
prong connectors.
Pretty simple.
I started with four strips, tested it out, and added two more so in total I had six strips
of lights going across.
I added trace paper to the underside to disperse the light even more.
First day of snow here in Wisconsin but I had to get one last piece, a little trim piece,
to tidy up the outside corners.
I used simple miters and attached it with brad nails and they are not perfect.
That's okay.
I wanted some power in this thing so I drilled a hole in the side and ran a power strip through
it.
It has some USB ports and your standard outlets.
This way I could charge things kind of out of sight if I needed to and also just hook
up the LEDs.
And finally I just screwed through the plastic housing on the light dial to attach it to
the side.
So I can use it to charge a bunch of different electronics at the same time.
Honestly I'll probably just use it to store my art supplies.
Check it.
If you enjoy drawing and tracing I hope this inspired you to build your own light table
and showed you that it's really not that difficult.
If you enjoyed this video it would be awesome if you could like it and also subscribe to
my YouTube channel.
And I'll have links below to all my social media stuff as well as my website.
I'll also upload the full time lapse of this drawing in case you're interested.
Thanks for watching.
